Panasonic PV25D52 PV20D52 User Guide - Page 47
Audio Output
View all Panasonic PV25D52 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 47 highlights
*Important: If a remote control button does not work when pressed, press the FM/TV, DVD button on the remote and try the button again. AUDIO OUTPUT Select the digital output to be output from the optical digital audio output connector of the unit. 1 Do steps 1 and 2 on page 46. 2 DVD MAIN MENU DISC LANGUAGES AUDIO OUTPUT ST I L L MODE : F I ELD TV MODE : Letterbox SELECT SET END : : SET : ACTION 1) Press to select "AUDIO OUTPUT." 2) Press SET to display screen. Recommended setting Type of amplifier to be connected LPCM Dolby (DVD) Digital dts No amplifier is connected OFF OFF OFF AV amplifier (with digital audio input connector) without Dolby Digital/dts decoder PCM*1 OFF*2 OFF*2 AV amplifier including Dolby Digital decoder PCM*1 Bitstream OFF AV amplifier including Dolby Digital/dts decoder PCM*1 Bitstream Bitstream*3 3 AUDIO OUTPUT LPCM(DVD) Dolby Digital dts DRC SURROUND : OFF : Bitstream : OFF : OFF : OFF SELECT SET END : : SET : ACTION 1) Press to select • Make settings according to amplifier connected to optical audio output as an item. shown in above table. 2) Press SET repeatedly for output. • When a dts decoder is not connected, to enjoy dts DVD, please select audio output other than dts on the dts DVD menu (See below.) screen. Otherwise, there will be no sound from the unit speakers. I "LPCM (DVD)" selections OFF: Linear PCM of less than 48 kHz/16 bit is output. When playing DVDs recorded in linear PCM of over 48 kHz/20 bit or 96 kHz, no digital audio is output. (Factory preset) PCM: When playing DVDs recorded in linear PCM of 48 kHz/20 bit/24 bit or 96 kHz, digital audio converted to 48 kHz/16 bit is output. (Digital output of PCM audio is restricted to 48 kHz/16 bit or below for copyright protection.) I "Dolby Digital" selections Bitstream: Dolby Digital bitstream (1ch-5.1ch) is output. (Factory preset) OFF: No output. *1 Audio output from unit is converted to 48 kHz/16 bit in addition to audio from digital audio output. To enjoy high quality sound at 48 kHz/ 20 bit /24 bit or 96 kHz, connect the amplifier or decoder directly to the audio output connectors, not to the digital audio output connector. [Select "OFF" at the "LPCM (DVD)".] *2 When connecting an amplifier (with an optical digital input connector) which does not contain the Dolby Digital or dts decoder, be sure to select "OFF". If "Bitstream" is selected, starting DVD I "dts" selections Bitstream: dts bitstream is output. (Factory preset) OFF: No output. I "DRC (Dynamic Range Compression)" selections OFF: Normal audio range is selected. (Factory preset) ON: For dynamic sound even at low volume, this is useful for late-night listening. [Dolby Digital DVDs play may cause such a high level of noise as to be harmful to your ears and damage the speakers. *3 When a dts decoder is connected, please select "Bitstream" in "dts". If "OFF" is selected, there will be no sound. only]. I "SURROUND" selections Surround Sound creates the effect of sound coming from non-existent rear speakers even when only connected to a 2-channel stereo system. Notes OFF: No Surround Sound effect. (Factory preset) ON: Surround Sound effect. • Turn off other surround effects when using this surround effect. 4 Press ACTION to redisplay DVD menu and go to step 2 to setup another item. Or, press ACTION three times to exit. • For optimum effect, the distance between the unit and the listener should be about 3 or 4 times the distance between the right and left front speakers. Advanced Operation 47