Panasonic PVD4752 PVD4742 User Guide - Page 10

Location of Controls continued

Get Panasonic PVD4752 - DVD/VCR DECK PDF manuals and user guides View all Panasonic PVD4752 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Location of Controls (continued) Rear View of DECK Bold: VCR Function Italic: DVD Function Bold Italic: VCR and DVD Functions AC Power Plug • While plugged into an AC outlet, this DECK consumes 4 W of electrical power in off mode. Component Video Output Connector (Y, PB, PR) (DVD Only) p. 13 SELECT SW (DVD Only) p. 13 VHF/UHF Antenna Output Terminal p.12 VHF/UHF Antenna Input Terminal p. 12 Video Output Connector p. 12 Video Input Connector p. 35 DVD OUTPUT DIGITAL AUDIO OUT (PCM/BITSTREAM) OPTICAL SEE MANUAL S-VIDEO OUT COMPONENT VIDEO OUT Y PB SELECT PR OUT L AUDIO2 •R OUT IN1 IN FROM ANT. VIDEO L AUDIO1 R• VHF/UHF OUT TO TV Optical Digital Audio Output Connector (DVD Only) p. 15 S-Video Out Connector (DVD Only) p. 10, 13 Audio Output 2 Audio Input Connector (L/R) Connector (L/R) p. 13 Audio Output 1 p. 35 Connector (L/R) p. 12 The following table shows the status of the output jacks when in VCR or DVD mode. Video Output Audio Out 1 Audio Out 2 Component Video Output S-VIDEO OUT VCR YES N/A N/A ➛ DVD YES YES SELECT SW (Switchable)➛YES Note • PROG functions on the remote are not available when using Component Video Output and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG. To enjoy PROGRESSIVE SCAN video (PV-D4752 only) (1). Connect Component Video Output to the component video input terminals of a television. (See p. 13.) (2). Set the "COMPONENT VIDEO OUT"/"S-VIDEO OUT" SELECT SWITCH, in the back of the DECK, to "COMPONENT VIDEO OUT." (See above.) (3). When the PROGRESSIVE button is pressed, the ON lamp lights up (see p. 9) and the PROGRESSIVE SCAN signal is output from the Component Video Output Connector. Note • The PROGRESSIVE button can be operated when the DECK is in DVD function mode. • The screen may shift off-center when using progressive output. Please adjust the screen position if this occurs. (Refer to your TV manual.) • The unit does not output video signals from the "VIDEO OUT" or "S-VIDEO OUT" terminals when the ON lamp is lit. 10 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
10
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Location of Controls (continued)
Rear View of DECK
AC Power Plug
S-Video Out
Connector
(DVD Only)
p. 10, 13
Component Video Output
Connector (Y, P
B
, P
R
) (DVD Only)
p. 13
Audio Output 2
Connector (L/R)
p. 13
Optical Digital Audio
Output Connector
(DVD Only)
p. 15
Video Input
Connector
p. 35
Video Output
Connector
p. 12
Audio Input
Connector (L/R)
p. 35
Audio Output 1
Connector (L/R)
p. 12
VHF/UHF Antenna Input Terminal
p. 12
VHF/UHF Antenna Output Terminal
p.12
DVD
OUTPUT
DIGITAL
AUDIO OUT
(PCM/BITSTREAM)
OPTICAL
S-VIDEO OUT
SELECT
COMPONENT
VIDEO OUT
Y
P
B
P
R
L
R
VIDEO
AUDIO1
L
R
OUT
IN1
IN FROM ANT.
OUT TO TV
VHF/UHF
OUT
AUDIO2
SEE MANUAL
•
While plugged into an AC outlet,
this DECK consumes 4 W of
electrical power in off mode.
•
•
The following table shows the status of the output jacks when in VCR or DVD mode.
Bold
:
VCR Function
Italic
:
DVD Function
Bold Italic
:
VCR and DVD Functions
Note
•
PROG functions on the remote are not available when using Component Video Output
and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press
PROG.
SELECT SW (DVD Only)
p. 13
Video Output
Audio Out 1
Audio Out 2
Component
Video Output
S-VIDEO OUT
VCR
DVD
YES
YES
N/A
N/A
To enjoy PROGRESSIVE SCAN video (PV-D4752 only)
(1). Connect
Component Video Output
to the component video input terminals of a television.
(See p. 13.)
(2). Set the
“
COMPONENT VIDEO OUT
”
/
“
S-VIDEO OUT
”
SELECT SWITCH
, in the back of the
DECK, to
“
COMPONENT VIDEO OUT.
”
(See above.)
(3). When the PROGRESSIVE button is pressed, the ON lamp lights up (see p. 9) and the
PROGRESSIVE SCAN signal is output from the
Component Video Output Connector
.
Note
•
The PROGRESSIVE button can be operated when the DECK is in DVD function mode.
•
The screen may shift off-center when using progressive output. Please adjust the screen
position if this occurs. (Refer to your TV manual.)
•
The unit does not output video signals from the
“
VIDEO OUT
”
or
“
S-VIDEO OUT
”
terminals
when the ON lamp is lit.
YES
SELECT SW
(Switchable)
➛
YES
➛