Panasonic SCHC05 SCHC05 User Guide - Page 1
Panasonic SCHC05 Manual
View all Panasonic SCHC05 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Supplied Accessories Check and identify the supplied accessories. Use numbers indicated in parentheses when asking for replacement parts. (Product numbers correct as of January 2011. This may be subject to change.) To order accessories, refer to "Accessory Purchases (United States and Puerto Rico)" on the next page. 1 x AC power supply cord (K2CB2CB00021) 1 x Remote control (RAK-SC989ZM) 1 x Lithium Button-Type battery (Battery is already installed in the remote control.) Owner's Manual Compact Stereo System Model No. SC-HC05 Dear Customer Thank you for purchasing this system. For optimum performance and safety, read these instructions fully before you connect, operate or adjust this system. Keep this manual for future reference. Your system and the illustrations can look differently. If you have any questions contact 1-800-211-PANA (7262) The warranty can be found on the next page. As an ENERGY STAR® Partner, Panasonic has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC caution: To maintain compliance with FCC regulations, shielded interface cables must be used with this equipment. Operation with non-approved equipment or unshielded cables may result in interference to radio and TV reception. Any changes or modifications not approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party: Panasonic Corporation of North America One Panasonic Way Secaucus, NJ 07094 Support Contact: Panasonic Consumer Electronics Company Telephone No.: 1-800-211-PANA (7262) WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance are not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter. CAUTION! DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE. ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS. WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE, • DO NOT EXPOSE THIS APPARATUS TO RAIN, MOISTURE, DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS. • USE ONLY THE RECOMMENDED ACCESSORIES. • DO NOT REMOVE THE COVER (OR BACK); THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. WARNING Risk of fire, explosion and burns. Do not disassemble, heat above 60°C (140°F) or incinerate. WARNING Keep the Button-Type battery out of reach of children to prevent swallowing. - If you see this symbol - Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal. Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America One Panasonic Way, Secaucus, New Jersey 07094 http://www.panasonic.com © Panasonic Corporation 2011 Printed in China P En Sp RQTX1316-2P L0111HH2031 IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE SCREWS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The model number and serial number of this product can be found on either the back or the bottom of the unit. Please note them in the space provided below and keep for future reference. MODEL NUMBER SC-HC05 SERIAL NUMBER User memo: DATE OF PURCHASE DEALER NAME DEALER ADDRESS TELEPHONE NUMBER The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Product identification marking is located on the bottom of unit. The unit should be installed near an accessible AC power outlet, with the power cord connected directly to it. To completely disconnect power from the unit, unplug the power cord from the AC power outlet. "Made for iPod" and "Made for iPhone" mean that an electronic accessory has been designed to connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, or iPhone may affect wireless performance. iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. < For USA-California only > This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Panasonic Corporation is under license. Other trademarks and trade names are those of their respective owners. Product service 1. Damage requiring service - The unit should be serviced by qualified service personnel if: (a) The AC power supply cord or the plug has been damaged; or (b) Objects or liquids have gotten into the unit; or (c) The unit has been exposed to rain; or (d) The unit does not operate normally or exhibits a marked change in performance; or (e) The unit has been dropped or the cabinet damaged. 2. Servicing - Do not attempt to service the unit beyond that described in these operating instructions. Refer all other servicing to authorized servicing personnel. 3. Replacement parts - When parts need replacing ensure the servicer uses parts specified by the manufacturer or parts that have the same characteristics as the original parts. Unauthorized substitutes may result in fire, electric shock, or other hazards. 4. Safety check - After repairs or service, ask the servicer to perform safety checks to confirm that the unit is in proper working condition. Product information For product information or assistance with product operation: Refer to "Customer Services Directory (United States and Puerto Rico)". Specifications Amplifier section RMS output power stereo mode Front Ch (both ch driven) 20 W per channel (6 ), 1 kHz, 10% THD Total RMS stereo mode power 40 W FTC output power stereo mode Front Ch (both ch driven) 15 W per channel (6 ), 20 Hz to 20 kHz, 10% THD Total FTC stereo mode power 30 W Terminal section AUX (rear) Terminal Stereo, 3.5 mm (1/8″) jack Speaker section Type 2 way, 2 speaker system (passive radiator) Speaker unit(s) Woofer Tweeter Passive radiators Impedance 6.5 cm (2 1/2″) cone type x 1/ch 1.5 cm (5/8″) piezo type x 1/ch 8 cm (3 1/8″) x 2/ch 6 Bluetooth® section Bluetooth® system specification Ver. 2.1 + EDR Wireless equipment classification Class 2 (2.5 mW) Support profiles A2DP, AVRCP Frequency band 2402 MHz to 2480 MHz (Adaptive Frequency Hopping) Driving distance 10 m (33 ft) line of sight (iPhone 4, at height 1 m (3.3 ft), in MODE 1) General Power supply AC 120 V, 60 Hz Power consumption 16 W Dimensions (W x H x D) 370 mm x 176 mm x 85 mm Mass (Weight) (14 1/2″ x 7″ x 3 1/2″) [D = 121 mm (4 3/4″) dock open] [D = 59 mm (2 1/2″) without stand] 1.8 kg (9 lb.) Operating temperature range 0°C to +40°C (+32°F to +104°F) Operating humidity range 35% to 80% RH (no condensation) Power consumption in standby mode 0.1 W (approximate) Note: 1. Specifications are subject to change without notice. Mass and dimensions are approximate. 2. Total harmonic distortion is measured by the digital spectrum analyzer. Getting started Remote control Before using Remove the insulation sheet before you use the remote control for the first time. Connect the AC power supply cord Rear view Insulation sheet Replacing the battery Replace the remote control battery when it stops operating or when the range is decreased. Replace with a new battery (CR2025) only. Stopper Battery holder 1 While pressing the stopper, pull out the battery holder. 2 Insert a new battery with the (+) side facing up. 3 Push the battery holder back fully. CAUTION! • Insert with poles aligned. • Do not touch the terminals (+ and -) with metal objects. • Do not recharge, disassemble, remodel, heat or throw into fire. • Keep out of reach of children. • Do not heat or expose to flame. • Do not leave the battery(ies) in an automobile exposed to direct sunlight for a long period of time with doors and windows closed. • Remove the battery if you do not use the remote control for a long period of time. Keep in a cool, dark area. If any electrolyte should come into contact with your hands or clothes, wash it off thoroughly with water. If any electrolyte should come into contact with your eyes, never rub the eyes. Rinse eyes thoroughly with water, and then consult a doctor. To household AC outlet • Use the included AC power supply cord with this system only. • Do not use an AC power supply cord from other equipment. Conserving power The system consumes approximately 0.1 W when it is in standby mode. Disconnect the power supply if you do not use the system. Some settings will be lost after you disconnect the system. You have to set them again. Speakers • Do not remove the speaker nets. • These speakers do not have magnetic shielding. Do not put them near TVs, PCs or other devices easily influenced by magnetism. • When you play at high levels for a long period, it can cause damage to the system and decrease the life of the system. • Decrease the volume when you play distorted sound to prevent damage. Overview of controls Top view iPod MENU OK SELECTOR LINK MODE PAIRING MUTE A Standby/on switch [`], [1, POWER] Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. B View the iPod or iPhone menu C Select an item D Confirm a selection Set or cancel the auto off function E Select iPod, Internet radio, Bluetooth® or AUX mode Bluetooth® is the default mode except when an iPod or iPhone is connected. F Start Bluetooth® pairing mode Select Bluetooth® link mode Adjust the audio input level in AUX mode G Adjust the volume of the system The setting returns to the default when you disconnect the AC power supply cord. H Mute the sound of the system In iPod mode : The light blue and green status indicators blink alternately. In Bluetooth® mode : The light blue and blue status indicators blink alternately. In AUX mode : The light blue status indicator blinks continuously. This function does not work when the system is pairing or waiting to connect with a Bluetooth® device. Press the button again to cancel. Mute is also canceled when you adjust the volume or when you switch off the system. I Start or pause playback J Skip or search track K Power indicator On : The system is on Off : The system is in standby mode L iPod or iPhone dock M Status indicator Green : iPod mode Blue : Bluetooth® mode Light blue : Set or cancel the auto off function Mute function is on Off : AUX mode The green status indicator blinks each time a remote control button is pressed. N [PUSH CLOSE] Press while closing the dock. O Remote control sensor Point the remote control at the remote control sensor, away from obstacles, at a maximum range of 7 m (23 ft) directly in front of the main unit. Maintenance To clean this system, wipe with a soft, dry cloth. • Never use alcohol, paint thinner or benzine to clean this system. • Before using chemically treated cloth, read the instructions that came with the cloth carefully. Using an iPod or iPhone Connecting an iPod or iPhone Preparation Update your iPod or iPhone with the latest software. Make sure to remove the iPod or iPhone from its case. 1 Push [x, iPod] to open the dock. Basic playback 1 Connect the iPod or iPhone. 2 Press [4/9] to start playback. Pause playback Press [4/9]. Press again to continue playback. Skip track Press [2] or [6]. Search track Press and hold [2] or [6]. View the iPod or Press [iPod MENU]. iPhone menu Select an item Press [R] or [T] and then press [OK]. Note: • Depending on the model, it may be necessary to remove the iPod or iPhone and select the album, artist, etc. on the iPod or iPhone. • Operation results may vary depending on the iPod or iPhone models. • Read the User Guide of the iPod or iPhone for operating instructions. 2 Insert a compatible dock adapter. 3 Connect the iPod or iPhone. The status indicator changes to green. iPhone (not included) Dock adapter (not included) Connector Hold the dock when connecting or disconnecting the iPod or iPhone. To close the dock 1 Disconnect the iPod or iPhone. 2 Press [PUSH CLOSE] while closing the dock. Note: • Make sure to align your iPod or iPhone with the connector when inserting. • Make sure to press [PUSH CLOSE] while closing the dock to prevent damage. • When an iPod or iPhone is connected, press [SELECTOR] to switch between modes (Internet radio, Bluetooth®, AUX or iPod). • The system automatically switches on when you connect an iPod or iPhone that is in playback mode (except for some models). • To purchase a dock adapter, consult your local iPod or iPhone dealer. Compatible iPod and iPhone (as of January 2011) • iPod touch 4th generation (8GB, 32GB, 64GB) • iPod nano 6th generation (8GB, 16GB) • iPod touch 3rd generation (32GB, 64GB) • iPod nano 5th generation (video camera) (8GB, 16GB) • iPod touch 2nd generation (8GB, 16GB, 32GB) • iPod classic [120GB, 160GB (2009)] • iPod nano 4th generation (video) (8GB, 16GB) • iPod classic (160GB) (2007) • iPod touch 1st generation (8GB, 16GB, 32GB) • iPod nano 3rd generation (video) (4GB, 8GB) • iPod classic (80GB) • iPod nano 2nd generation (aluminum) (2GB, 4GB, 8GB) • iPod 5th generation (video) (60GB, 80GB) • iPod 5th generation (video) (30GB) • iPod nano 1st generation (1GB, 2GB, 4GB) • iPhone 4 (16GB, 32GB) • iPhone 3GS (8GB, 16GB, 32GB) • iPhone 3G (8GB, 16GB) • iPhone (4GB, 8GB, 16GB) Compatibility depends on the software version of your iPod or iPhone. Note: • The display on the iPod can show differently because of the compatibility of the iPod models. • All phone features can only be controlled by the touch screen of the iPhone. • The system does not show incoming calls or the phone status. • Playback will stop when there is an incoming call. Disconnect the iPhone to answer the call. • A call is not canceled when you connect or disconnect the iPhone from the system. • There is no Apple Inc. specification that will guarantee the above iPhone response. iPhone responses can be different on newer models or with newer software. Charging an iPod or iPhone An iPod or iPhone is charged automatically when connected to the system (even when the system is in standby mode). • See the iPod or iPhone display for its battery charging status. • Disconnect the iPod or iPhone if it is not used for an extended period of time after charging is complete. • Charging stops when the battery is fully charged. The battery will deplete naturally. Listening to the Internet radio You can listen to a radio station on the Internet if you install the "vTuner for Panasonic" application on your iPod touch or iPhone. Download this application from the App Store. Note: For compatible iPod touch and iPhone models and instructions on how to use the "vTuner for Panasonic" application, refer to: http://radio.vtuner.com/panasonic/en/ Preparation Install "vTuner for Panasonic" on your iPod touch or iPhone. Connect your iPod touch or iPhone to the Internet. Go to the Home screen of the iPod touch or iPhone. 1 Connect the iPod touch or iPhone. 2 Press [SELECTOR] to start the application. Using the auto off function The system automatically switches off if there is no audio input and you do not use it for approximately 30 minutes. 1 Press [SELECTOR] to select AUX mode. Status indicator: Off 2 Press and hold [OK]. ON ↔ OFF (default) ON : The light blue status indicator blinks 2 times. OFF : The light blue status indicator blinks 1 time. Note: • This function does not work when a Bluetooth® device is connected. • 1 minute before the system switches off, the power indicator blinks. • The setting returns to the default when you disconnect the AC power supply cord.