Panasonic TC P50V10 50" Plasma Tv - Page 45

Select LAN speed setting Default is Automatic, Select Software update

Get Panasonic TC P50V10 - 50inch Plasma TV PDF manuals and user guides
UPC - 037988242511
View all Panasonic TC P50V10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Network Setting Check that the network settings are as shown below, and then start "Connection test". Select "Connection test" and press OK. *Press OK again to cancel the test. (It takes a while to cancel the test.) Network setting Connection test IP setting mode IP address Subnet mask Default gateway 1/2 Succeeded Manual 192.168.0.5 255.255.255.0 192.168.0.254 select ok Succeeded: "Connection test" succeeded Only home network: Home network is available. Failed: Check the broadband environment connection and settings and the network settings, and then perform the test again. Test in progress ---: Test not yet performed ■ Select "IP setting mode" and set to "Automatic". Manual setting (When IP automatic acquisition in DHCP can be used) Network setting Connection test 1/2 Succeeded select Select "IP setting mode" and set to "Manual" Select the item and press OK Check the specifications of the broadband router and IP setting mode Automatic enter each IP address. IP address 192.168.0.5 Subnet mask 255.255.255.0 ok Default gateway 192.168.0.254 Subnet mask 100I . 0OK. 0 . 0 The acquired address is displayed. Each IP address is acquired automatically. or change channel ok ■ Select "DNS setting mode" and set to "Automatic". Manual setting (When DNS automatic acquisition in DHCP can be used) Network setting Connection test Default gateway IP setting mode DNS setting mode Primary DNS 1/2 Succeeded 192.168.0.254 Automatic AutoOmKatic 192.168.0.20 select ok Select "DNS setting mode" and set to "Manual" Select the item and press OK Enter each IP address as was specified by the provider. Secondary DNS 192.168.0.21 Primary DNS 100I . 0 . 0 . 0 The acquired address is displayed. Each IP address is acquired automatically. If you are using a broadband router, IP automatic acquisition in DHCP can be used under normal circumstances. If you are not sure, check with the person who installed the equipment, or check the instructions for each device. or select ok Select "LAN speed setting" (Default is "Automatic") Network setting LAN speed setting LAN speed Software update MAC address 2/2 Automatic 10BASE half duplex 12-34-56-78-80-ab select adjust Normally, select "Automatic". If "Connection test" failed, set the "LAN speed setting" to "manual" and then select "10BASE half duplex", "10BASE duplex", "100BASE half duplex" or "100 BASE duplex". Cannot be selected when the "LAN speed setting" is "Automatic". Changing the settings may make it impossible to connect some types of equipment. Select "Software update" Network setting LAN speed setting LAN speed Software update MAC address 2/2 AutoOmKatic 10BASE half duplex 12-34-56-78-80-ab select ok Press OK to start the software update screen. Follow directions of the screen. * Set "Clock" first. (p. 18) Advanced The network settings become effective when you close the menu and run "Connection test". 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
45
Advanced
Network Setting
The network settings become effective when you close the menu and run “Connection test”.
Check that the network settings are as shown below, and then start “Connection test”.
Select “Connection test” and press OK.
Succeeded
: “Connection test” succeeded
Only home network:
Home network is available.
Failed:
Check the broadband environment connection
and settings and the network settings, and then
perform the test again.
Test in progress
---:
Test not yet performed
*Press OK again to cancel the test.
(It takes a while to cancel the test.)
Network setting
1/2
Connection test
Succeeded
IP setting mode
Manual
IP address
192.168.0.5
Subnet mask
255.255.255.0
Default gateway
192.168.0.254
select
ok
Select “IP setting mode” and set to “Automatic”.
■
Manual setting
Select “IP setting mode” and set to “Manual”
Select the item and press OK
Check the specifications of the broadband router and
enter each IP address.
(When IP automatic acquisition in DHCP can be used)
Network setting
1/2
Connection test
Succeeded
IP setting mode
Automatic
IP address
192.168.0.5
Subnet mask
255.255.255.0
Default gateway
192.168.0.254
The acquired address is displayed.
select
ok
Subnet mask
0
.
0
.
0
.
0
change
channel
ok
or
Each IP address is acquired automatically.
Select “DNS setting mode” and set to “Automatic”.
(When DNS automatic acquisition in DHCP can be used)
Network setting
1/2
Connection test
Succeeded
Default gateway
192.168.0.254
DNS setting mode
Primary DNS
192.168.0.20
Automatic
Secondary DNS
192.168.0.21
The acquired address is displayed.
select
ok
Each IP address is acquired automatically.
If you are using a broadband router, IP automatic
acquisition in DHCP can be used under normal
circumstances. If you are not sure, check with the
person who installed the equipment, or check the
instructions for each device.
■
Manual setting
Select “DNS setting mode” and set to “Manual”
Select the item and press OK
Enter each IP address as was specified by the
provider.
Primary DNS
0
.
0
.
0
.
0
select
ok
or
Select “LAN speed setting” (Default is “Automatic”)
Normally, select “Automatic”.
If “Connection test” failed, set the “LAN speed setting”
to “manual” and then select “10BASE half duplex”,
“10BASE duplex”, “100BASE half duplex” or “100 BASE
duplex”.
Cannot be selected when the “LAN speed setting” is
“Automatic”.
Changing the settings may make it impossible to
connect some types of equipment.
Network setting
2/2
MAC address
12-34-56-78-80-ab
LAN speed setting
Automatic
LAN speed
10BASE half duplex
Software update
select
adjust
Select “Software update”
Press OK to start the software update screen.
Follow directions of the screen.
* Set “Clock” first. (p. 18)
Network setting
2/2
MAC address
12-34-56-78-80-ab
LAN speed setting
Automatic
LAN speed
10BASE half duplex
Software update
select
ok