Panasonic TH-42PH11UK 42" Plasma Tv - Page 10

PC Input Terminals connection - th resolution

Get Panasonic TH-42PH11UK - 42inch Plasma Panel PDF manuals and user guides
UPC - 037988242085
View all Panasonic TH-42PH11UK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Connections PC Input Terminals connection COMPUTER (Female) AUDIO PC IN Conversion adapter (if necessary) RGB PC cable Mini D-sub 15p (Male) Audio Stereo plug Connect a cable which matches the audio output terminal on the computer. Notes: • Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.) • The display resolution is a maximum of 768 × 768 dots (TH-42PH11UK), 1,024 × 768 dots (TH-50PH11UK) when the aspect mode is set to "4:3", and 1,024 × 768 dots (TH-42PH11UK), 1,366 × 768 dots (TH-50PH11UK) when the aspect mode is set to "FULL". If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. • The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection. • Some PC models cannot be connected to the set. • There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal. • The computer shown in the illustration is for example purposes only. • Additional equipment and cables shown are not supplied with this set. • Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. • Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector. • Change the "COMPONENT/RGB-IN SELECT" setting in the "SET UP" menu to "COMPONENT" (when COMPONENT signal connection) or "RGB" (when RGB signal connection). (see page 34) Signal Names for Mini D-sub 15P Connector 54 321 10 9 8 7 6 15 14 13 12 11 Pin Layout for PC Input Terminal Pin No. 1 2 3 4 5 Signal Name R (PR/CR) G (Y) B (PB/CB) NC (not connected) GND (Ground) Pin No. 6 7 8 9 10 Signal Name GND (Ground) GND (Ground) GND (Ground) +5 V DC GND (Ground) Pin No. 11 12 13 14 15 Signal Name NC (not connected) SDA HD/SYNC VD SCL 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
AUDIO
PC IN
10
PC Input Terminals connection
Notes:
• Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning
frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
• The display resolution is a maximum of 768 × 768 dots (TH-42PH11UK), 1,024 × 768 dots (TH-50PH11UK) when the
aspect mode is set to “4:3”, and 1,024 × 768 dots (TH-42PH11UK), 1,366 × 768 dots (TH-50PH11UK) when the aspect
mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show
fi
ne detail with
suf
fi
cient clarity.
• The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need
to make setting changes to the computer at the time of connection.
• Some PC models cannot be connected to the set.
• There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.
• The computer shown in the illustration is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the speci
fi
ed
frequency range.
• Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.
• Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT”
(when COMPONENT signal connection) or “RGB” (when RGB signal connection). (see page 34)
Signal Names for Mini D-sub 15P Connector
Pin Layout for PC Input
Terminal
COMPUTER
Conversion adapter
(if necessary)
Mini D-sub 15p
RGB
PC cable
Stereo plug
Audio
Connect a cable which matches
the audio output terminal on the computer.
1
6
7
8
3
9
4
5
10
15
14
13
12
11
2
Pin No.
Signal Name
Pin No.
Signal Name
Pin No.
Signal Name
1
R (P
R
/C
R
)
6
GND (Ground)
11
NC (not connected)
2
G (Y)
7
GND (Ground)
12
SDA
3
B (P
B
/C
B
)
8
GND (Ground)
13
HD/SYNC
4
NC (not connected)
9
+5 V DC
14
VD
5
GND (Ground)
10
GND (Ground)
15
SCL
Connections
(Male)
(Female)