Panasonic TH65PF9UK TH65PF9UK User Guide - Page 9

Connections - manual

Get Panasonic TH65PF9UK - 65inch PLASMA MONITOR PDF manuals and user guides View all Panasonic TH65PF9UK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Connections When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker's Installation Manual for details on speaker installation. Speakers (Optional accessories) 1 2 1 SPEAKERS Terminals (R) 2 SPEAKERS Terminals (L) AC cord connection (see page 13) - AC cord fixing 31 1 Connect the AC cord plug to the Plasma Display. 2 Fix the left side clamper. 3 Fix the right side clamper. Close Open 2 Push until the hook clicks. 2. Pull off. Note: The power plug in the illustration may not be the type fitted to your set. 1. Keep the knob pressed. - Cable fixing bands Secure any excess cables with bands as required. Pass the attached cable fixing band through the clip as shown in the figure. To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure. While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band. To tighten: To loosen: Push the catch Pull 1 2 Pull SLOT1 AUDIO DVI-D IN SLOT2 R AUDIO L PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN SLOT3 AUDIO PC IN SERIAL Optional Terminal DVI-D IN COMPONENT/RGB IN Board Insert Slot Terminals and Audio IN Terminals (covered) (see page 12) (see page 12) From EXTERNAL monitor terminal on Computer (see page 10) Note: At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3. From SERIAL Terminal on Computer (see page 11) 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
9
Connections
1
3
2
1
2
SERIAL
PC
IN
AUDIO
SLOT1
SLOT3
P
R
/C
R
/R
P
B
/C
B
/B
Y/G
AUDIO
R
L
COMPONENT/RGB IN
SLOT2
AUDIO
DVI-D IN
1
2
1
2
SPEAKERS
Terminals (R)
SPEAKERS
Terminals (L)
– Cable fixing bands
Secure any excess cables with bands as required.
When connecting the speakers, be sure to use only the optional accessory speakers.
Refer to the speaker’s Installation Manual for details on speaker installation.
Speakers (Optional accessories)
Pass the attached cable
fixing band through the
clip as shown in the
figure.
To secure cables connected to Terminals, wrap the cable fixing band around them then
pass the pointed end through the locking block, as shown in the figure.
While ensuring there is sufficient slack in cables to minimize stress (especially
in the power cord), firmly bind all cables with the supplied fixing band.
From SERIAL
Terminal on Computer
(see page 11)
From EXTERNAL
monitor terminal on
Computer (see page 10)
AC cord connection (see page 13)
DVI-D IN
Terminals
(see page 12)
To tighten:
To loosen:
Pull
Pull
Push the catch
Note:
At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3.
– AC cord fixing
Optional Terminal
Board Insert Slot
(covered)
COMPONENT/RGB IN
and Audio IN Terminals
(see page 12)
Note:
The power plug in the illustration may not be the type fitted to
your set.
1
Connect the AC cord plug to
the Plasma Display.
2
Fix the left side clamper.
3
Fix the right side clamper.
Close
Open
Push until the hook clicks.
2.
Pull off.
1.
Keep the knob pressed.