Panasonic WV-SPV781L Installation Guide - Page 2

The installation tasks are explained using 5 steps. Step1 Preparations Installation Step2 Attaching the safety wire Step3 Fixing the camera Step4 Adjusting the camera Step5 Perform camera settings (see the separate leaflet) Step1 Preparations There are 3 methods to install the camera to a ceiling or wall as described below. Prepare the required parts for each installation method before starting the installation. The following are the requirements for the various installation methods. 2Fit the Safety wire lug to the camera. I Wire lug fixing screw (accessory) J Safety wire lug (accessory) Recommended tightening torque: 0.6 N·m {0.44 lbf·ft} Installation method Recommended screw Minimum pullout strength [1] Directly mount the camera onto the ceiling or wall (when there is a space for wiring in the ceiling or the wall) M5 screws x 4 724 N {163 lbf} (per 1 pc.)*1 [2] Mount the camera to a junction box * Only use metal junction boxes. M4 screws x 4*2 724 N {163 lbf} (per 1 pc.)*1 [3] Mount the camera onto the ceiling or wall using the adapter box (approx. 510 g {1.13 lbs}) (when there is no space for wiring in the ceiling or the wall) M5 screws x 4 724 N {163 lbf} (per 1 pc.)*1 Step 3 Fixing the camera * The safety wire is not shown in the subsequent illustrations. *1 To mount the camera onto the ceiling or wall, the H safety wire (accessory) must be attached. Have an M6 bolt and nut or anchor (with the minimum pullout strength of 724 N {163 lbf}) ready for securing the safety wire. *2 Prepare a M4 screw with a washer with a diameter of 7.5 mm {5/16 inches} to 10 mm {3/8 inches} and a spring washer. IMPORTANT: ●● For the screws or anchor bolts used in the above methods ([1] to [3]), be sure to secure the minimum pull-out strength of 724 N {163 lbf} per screw or bolt. ●● Select screws according to the material of the ceiling or wall that the camera will be mounted to. In this case, wood screws and nails should not be used. ●● If a ceiling or wall board such as plaster board is too weak to support the total weight, the area shall be sufficiently reinforced. ●● Because the front cover is temporarily removed when installing or adjusting the camera, make sure no liquid enters the camera at these times. Step 2 Attaching the safety wire 1 Pass the H safety wire (accessory) H Safety wire through the wire mounting hole in (accessory) the J Safety wire lug (accessory). J Safety wire lug (accessory) Wire fitting Wire mounting hole [1]Directly mount the camera onto the ceiling or wall 46 mm {1-13/16 inches} 23 mm {29/32 inches} 1 Determine the position where the camera is to be mount- ed on the ceiling or wall and drill a hole for securing the camera and wiring as shown in the illustration to the right. * Determine the diameter and depth of the hole according to the Cable access hole ø30 mm {1-3/16 inches} 35 mm {1-3/8 inches} size of fixing screws or anchors (4 M5 screws, locally procured). 2 Connect the cables coming from the camera and com- ing through the ceiling or wall according to the instructions in "Making connections". Waterproof the connections according to the instructions in "Waterproof treatment for the cable joint sections". 83.5 mm {3-5/16 inches} 3 Secure the camera to the camera mount bracket by attaching the 2 upper M5 screws or anchors (M5 x 4, locally procured) and then the 2 lower ones into the holes on side B on the camera mount bracket in the order shown in the illustrations above explanations [1]-1 to [1]-3 in the lower left. 4 Secure the A camera mount bracket cover (accessory) to the camera mount bracket by using M3 x 6 mm {1/4 inches} B Camera mount bracket cover fixing screws (accessory). Note: ●● When installing on a wall, install the camera mount bracket so that "↑ TOP/ FRONT" faces upward. ●● When installing on a ceiling, install the camera mount bracket so that "↑ TOP/ FRONT" is aligned with the direction in which the camera is pointed. Direction in which "↑TOP/FRONT" is pointed Direction in which the camera is pointed Example: When mounting on a ceiling [3] Mount the camera onto the ceiling or wall using the L Adapter box (accessory) Step 3 Fixing the camera (continued from upper right) * The following explains an example of Cable access hole ø30 mm mounting the camera on a wall. 24.5 mm {15/16 inches} 83.5 mm {3-5/16 inches} Side B (upper) ↑ TOP/FRONT mark A Camera mount bracket cover (accessory) 46 mm {1-13/16 inches} 23 mm {29/32 inches} View from above (internal) {1-3/16 inches} 1 Secure the adapter box to the wall. ●● Drill pilot holes and a cable hole (see the illus- tration to the left for their dimensions). (Drill pilot holes only if making connections through 6 mm {1/4 inches} wide x the cable hole from the side.) 2 PAN lock screws 10 mm {3/8 inches} length hole ●● Be sure to face "TOP" inside the adapter box upward. M5 x 2 (locally procured) TILT lock screw Camera mount bracket (the other one is on the opposite side) B Camera mount bracket cover fixing screws (accessory) Screws x 4 (M5, locally procured) ●● Use 4 screws (locally procured) to directly secure TOP the adapter box to the wall. Minimum pull-out strength: 724 N {163 lbf} (per 1 pc.) Center of the adapter box L Adapter box (accessory) ●● To install this product outdoors, be sure to waterproof the screws and their holes. 2 Temporarily secure the camera mount bracket and camera to the adapter box. Cable access hole ●● After referring to [1]-1 and adjusting the camera to (Used when connecting to a conduit. face down, temporarily secure the camera, and then M5 x 2 (locally procured) [1]-1 Loosen the TILT lock [1]-2 Loosen the 2 PAN screw by about 1 turn until lock screws about 1 the camera faces downward turn until the camera [1]-3 Using the B camera mount bracket cover fixing screws (accessory), install the A Supports G3/4 parallel screws.) N Adapter box mounting screw (accessory) M4 × 35 mm {1- 3/8 inches} hinges ↑TOP/FRONT mark (on the front) use the M4 × 35 mm {1- 3/8 inches} N Adapter box mounting screw (accessory) for installing the camera to temporarily install the camera mount bracket to the left or right hinge of the adapter box so that it can be opened and closed. ●● Secure the camera mount bracket with "↑TOP/ and then temporarily tighten the TILT lock screw. After this, use the 2 upper M5 screws (locally procured) to secure the camera. faces upward and use the 2 lower M5 screws (locally procured) to secure the camera. camera mount bracket cover (accessory) with the camera facing downward. Recommended tightening torque: 0.6 N·m {0.44 lbf ft} FRONT" facing upward. ●● When the wall is on one side or the other, install the adapter box to the hinge on the opposite side of the wall. ●● Secure the camera mount bracket to the hinge of the adapter box using the following tighten- * M5 x 4 screws, Minimum pull-out strength: 724 N {163 lbf} (per 1 pc.). Secure the ing torque. Recommended tightening torque: camera through the holes in side B of the camera mount bracket. [2] Mount the camera to a junction box As shown in the illustration to the right, install the camera to a junction box using 4 M4 fixing screws (locally procured) via the holes in side B of the camera mount bracket. (Minimum pull-out strength: 724 N {163 lbf} (per 1 pc.)) Side B (Upper) Junction 46 mm box {1-13/16 inches} L Adapter box (accessory) Camera mount bracket 0.78 N·m {0.58 lbf·ft} 3 Connect the cables. ●● Connect the cables coming from the camera and coming through the wall according to the instructions in "Making connections". M Mounting screws for adapter box(accessory) x 4 A Camera mount bracket cover (acces- ●● Waterproof the connections according to the instructions in "Waterproof treatment for the cable joint sections". sory) x 2 4 Secure the camera mount bracket to the adapter box. ●● Using 4 M5 x 20 mm {13/16 inches} M Note: ●● The procedure for fitting screws in the holes Mounting screws for adapter box (accessory), secure the camera mount bracket to the adapter box via the holes in side A of the cam- for connections and fixing screws is the era mount bracket in the order of the top 2 same as for 2, 3, and 4 in [1] Directly holes to bottom 2 holes. Recommended tight- mount the camera onto the ceiling or wall. ●● When junction boxes or the like are used, it is recommended that 2 pieces be used side by side. (Securing the camera to one junction box and making connections to the other makes cable connections easy.) 83.5 mm Camera {3-5/16 inches} mount bracket Side A (lower) B Camera mount bracket cover fixing screws (accessory) x 2 ening torque: 1.86 N·m {1.37 lbf ft} (Refer to [1]-1 and [1]-2.) ●● Using 2 M3 x 6 mm {1/4 inches} B camera mount bracket cover fixing screws (accessory), secure the A Camera mount bracket cover (accessory) to the Camera mount bracket. Recommended tightening torque: 0.6 N·m {0.44 lbf ft} Step 4 Adjusting the camera 1, 2, 3, 4, 5 D) Using a 5 mm {3/16 inches} hex wrench (locally procured), loosen the Yawing lock screw, turn the camera until the sunshield faces up and adjust the tilt of the cam- 1 Change the direction the camera is facing from directly down to facing up (as shown in the illustration on the lower right) and temporarily fix the camera in place. After this, loosen the 4 fixing screws on the camera front cover and remove the front cover together with the K Protection cover (accessory). era. (Yaw range: -115° to +200°) E) Press the WIDE or TELE button to adjust the field of view. IMPORTANT: ●● The front cover is connected to the camera via the auxiliary wire for mounting the front cover as well as the IR LED cable. Do not remove the auxiliary wire and IR LED cable. ●● Do not remove the K Protection cover (accessory) from the front cover. SD memory card (Ensure that the label faces the lens.) F) Adjust the camera angle and field of view by repeating steps A) through E). When the desired angle and field of view are achieved, tighten the 2 PAN lock screws, TILT lock screw and Yawing lock screw. Recommended tightening torque PAN lock screw: 2.7 N·m {2.0 lbf ft} TILT lock screw: 4.3 N m {3.2 lbf ft} Yawing lock screw: 2.7 N m {2.0 lbf ft} IMPORTANT: 2 Fit a pin cable (locally procured) to the ●● After adjustment, be sure to tighten the PAN, TILT and Yawing lock screws. MONITOR OUT jack on the camera and connect an adjustment monitor. Note: 3 Turn on the camera. 4 Insert an SD memory card into the slot, if necessary. Auxiliary wire Front cover Insert the SD memory card with its label facing the lens. Protection cover ●● To remove the SD memory card, hold down retaining tape the SD ON/OFF button for about 2 seconds. K Protection cover When the blinking SD MOUNT indicator goes (accessory) out, you can remove the SD memory card. ●● After the SD memory card has been replaced, press the SD ON/OFF button (for Front cover fixing screws less than 1 second), and make sure the SD * The front cover, including the cables and wires, ●● Any of the PAN, TILT and YAW lock screws can be adjusted by loosening them about 1 turn. Do not unscrew them more than necessary. ●● Make sure the camera is supported when loosening screws and adjusting the direction of the camera. ●● When the image size is adjusted using the WIDE or TELE button, the camera focus is adjusted accordingly by the auto-focus coarse adjustment function. ●● When the camera is mounted on the wall, adjust the camera direction by turning the PAN, TILT and YAW parts as shown in the illustration below. ●● The range of angles that the camera can actually be turned to in regards to a wall or ceiling is as follows. MOUNT indicator is continually lit. ●● If you do not press the SD ON/OFF button after replacing the SD memory card, the SD MOUNT indicator is automatically lit approximately 5 minutes later. and the front cover protector are not shown in the subsequent illustrations. 5 Adjust the camera field of view. Adjust the direction of the camera with the PAN, TILT and YAW parts, and press the WIDE or TELE button until the desired field of view is achieved. A) Using a 5 mm {3/16 inches} hex wrench (locally procured), loosen the PAN lock screw on either side of the base of camera arm. To direct the camera to the left, turn the screw clockwise when viewed from the front. To direct the camera to the right, turn it counterclockwise. (Panning range: + 180° to - 180°) B) Using a 5 mm {3/16 inches} hex wrench (locally procured), loosen the TILT lock screw in the center of camera arm and roughly adjust the direction of the camera. (Tilting range: 0° to 115°) C) Temporarily tighten 2 PAN lock screws and 1 TILT lock screw to prevent the camera from moving. Wall mounting Ceiling mounting Angle Adjustment part Angle Adjustment part Horizontal ±115° TILT rotation part* ±180° PAN rotation part Vertical ±115° TILT rotation part* 0° to 115° TILT rotation part Yaw from -115° to YAW rotation from -115° to YAW rotation +200 part +200 part * You can change between horizontal and vertical angles by adjusting the PAN rotation part. * D o not adjust the PAN rotation part more than ±180°. This may cause 5*-5
SPUBUJPO
QBSU IMPORTANT: ●● Avoid touching the tilting part near the warning label when you change the tilting angle to secure the cam- Warning label cables to be wrenched. :"8
SPUBUJPO
QBSU 1"/
SPUBUJPO
QBSU era. ●● If the TILT or PAN lock screw is loosened, the camera may not be held in place when it is secured to the wall or ceiling. If this is the case, temporarily tighten the appropriate lock screws to keep the camera from moving. $BNFSB
BSN
QBSU Step 4 Adjusting the camera (continued) 6, 7, 8, 9 6After adjusting the focus by pressing the AF button, remove the adjustment monitor. 7Attach the front cover. Tilt lock screw x 1 Yawing lock screw x 1 PAN lock screws (The other one is on the opposite side) x 2 * The front cover, including cables and wires, and Protection cover are not shown in the illustration. IMPORTANT: ●● Securely tighten the 4 front cover fixing screws. Failure to do so may cause the camera to fall or waterproof failure. Recommended tightening torque: 0.6 N·m {0.44 lbf·ft} Note: ●● When closing the front cover, be sure not to allow the IR LED cable to be caught in the cover. Auxiliary wire Front cover Protection cover retaining tape K Protection cover (accessory) IMPORTANT: ●● Each M6 bolt and nut or anchor (locally procured) for securing the H safety wire (acces- sory) must have the minimum pull-out strength of 724 N {163 lbf}. ●● Be sure to secure the H safety wire (accessory) to the foundation of a structure or an area that is strong enough. ●● Be sure to install the camera at least 2m 80 cm {9.2 feet} from the floor (the distance between the lowest part of the installed camera and the floor). ●● When installing on a wall, secure the H safety wire (accessory) to an area above the camera and the location where the camera is installed. ●● Attach the H safety wire so that if the camera were to become detached, it would not fall on nearby people. 9 Remove the K Protection cover (accessory). 8Secure the H safety wire (accessory) to the ceiling or wall. ■ When the camera is installed to the ceiling Ceiling Ceiling H Safety wire (accessory) Front cover fixing screws ■ When the camera is mounted on the wall Wall H Safety wire (accessory) M6 bolt and nut or anchor (locally procured) M6 bolt and nut or anchor (locally procured) When the camera has been installed, remove the protection cover from the front cover. After removal, be sure not to touch the clear part of the front cover. IMPORTANT: ●● Once the front cover is installed, the camera may be slightly out of focus. After installing the front cover and K Protection cover (accessory), use the auto focus via the settings menu. Clear part of the front cover K Protection cover (accessory) Note: ●● When removing the camera, perform removal by following the installation procedure in the reverse order. ●● After the installation is complete, store the K Protection cover (accessory) for use dur- ing servicing. H Safety wire (accessory) Wall H Safety wire (accessory) Step 5 Configuring the settings of the camera (see the leaflet) When the installation of the camera is complete, perform camera settings while referring to the included "Configure the settings of the camera" (leaflet).