Panasonic WVCW244F WVCW244F User Guide - Page 1

Color CCTV Camera Operating Instructions Model No.WV-CW244F WV-CW244S Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. N0803-1093 3TR001693BAA Printed in Japan CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. SA 1965 SA 1966 The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. For U.S.A NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. For Canada This Class A digital apparatus complies with canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. The serial number of this product may be found on the top of the unit. You should note the serial number of this unit in the space provided and retain this instruction as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No. WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. PREFACE The WV-CW244 series is a 1/3" CCD color camera designed for use in a video surveillance system. The camera features a high picture quality thanks to the use of digital signal processing LSIs, and easy installation. FEATURES • Mounting method: Flash mounting/WVCW244F, Surface mounting/WV-CW244S • Signal processing: Automatic Light Control (ALC), Automatic Gain Control (AGC), Automatic Tracing White Balance (ATW), etc. • Synchronization: Internal, Line-Lock (only 24 V AC), and Multiplexed Vertical Drive (VD2) • Minimum illumination: 2.4 lx (0.24 foot-candle) at WIDE • Signal-to-noise ratio: 50 dB (Equivalent to AGC OFF) • Horizontal resolution: 480 TV lines • Optional heater unit available for the cam- era used at temperatures between -10 ˚C and -30 ˚C (14˚F and -22˚F). PRECAUTIONS 1. This product should be installed and connected by qualified service personnel or system installers in conformity with NEC. 2. Use a class 2 power source supplying 12 V DC or 24 V AC. 3. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) to connect the power supply to the camera. 4. Be sure to use a ceiling board/wall having enough strength to support this camera. 5. Handle the camera with care. Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or storage. 6. Do not use strong or abrasive detergents. Use a dry cloth to clean the camera body when dirty. In case the dirt is hard to remove, use a mild detergent and wipe gently. Afterwards, wipe off the remaining detergent with a dry cloth. 7. Clean the lens faceplate with care. Do not clean the lens with strong or abrasive detergents. Use lens tissue or a cotton tipped applicator and ethanol. 8. Never face the camera towards the sun. Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may be caused. 9. Do not operate the camera beyond its specifications. Use the camera under conditions where temperature is between -10 °C to +50 °C (14 °F to 122 °F), and humidity is below 90 %. The input power source is 24 V AC or 12 V DC. 10. Use a monitor whose resolution is at least equal to that of the camera. MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS qw 2nd transport protection screw (Red) Space for heater unit u e r i o t !0 y OFF ON ON 123 SYNC LL INT* BLC OFF* ON !1 AP SOFT SHARP* * Default setting q Focus lock lever Fixes the focus position after adjusting. w Tilting lock screw Fixes the tilting position after adjusting. e Zoom lock lever Fixes the zoom position after adjusting. r Panning table Adjusts the panning angle of the camera. t Azimuth adjuster Adjusts the azimuth angle to obtain a level image. y Pan lock screw Fixes the panning position after adjusting. u Heater power connector Supplies power to the optional heater unit when it is built in the camera. Connect here a harness sticking out from the heater unit. i Synchronization Mode Selector Specifies a source for synchronization. INT: Internal 2:1 interlace. LL: Line-lock mode driven by 24 V AC. The default setting is INT. Note: Do not set the switch to LL (LineLock) position when supplying 12 V DC to avoid synchronization error. o Back Light Compensation Selector ON: Compensates the background if it is brighter than the object. OFF: Does not compensate. The default setting is OFF. !0 Aperture Level Selector SHARP: Sharpens the image outline. SOFT: Softens the image outline. The default setting is SHARP. !1 Video jack (3.5-diam. mini jack) For connecting an LCD monitor to adjust the camera images. Use an L-type plug to save space. 83.5mm (3-5/16") 85 mm (3-3/8") 51 mm (2") !2 !3 !4 !5 !6 !2 Dome cover !3 Video output cable with BNC connector Connects with the video connector of the monitor. !4 Camera power cable Supplies 24 V AC or 12 V DC from an external power source. !5 Heater power cable Supplies 24 V AC from an external power source to an optional heater. !6 Camera mounting bracket Only WV-CW244S (surface mount type) is supplied with a mounting bracket for ceiling installation. INSTALLATION ■ Installation Plans & Preparations ● WV-CW244F "F" stands for flash mounting. This model can be mounted on a two-gang junction box (4" x 4") preinstalled in the wall or ceiling. 46mm (1-13/16") Camera fixing screw x 4 (procured locally) 1. Space Prepare a space larger than ø160 mm. 2. Junction box Procure and install a junction box that meets the dimensions in the figure. 3. Camera Fixing Screws Procure four screws (M4) suitable for the junction box. 4. Cable route Cables will go behind the junction box. 5. Waterproof Process When necessary, apply waterproof process to the camera and relevant portions. Be sure to apply silicone rubber to the camera fixing screws in case of outdoor installation. ● WV-CW244S "S" stands for surface mounting. This model can be installed on the surface of the wall or ceiling using the supplied bracket. 85 mm (3-3/8") Cable access hole for 3/4" pipe Bracket fixing screw x 4 (procured locally) Bracket center Camera fixing screw x 4 (supplied) 1. Space Prepare a space larger than ø160 mm. 2. Bracket Fixing Screws To fix the bracket, procure four M4 screws suitable for the surface and structure of the wall/ceiling. 3. Camera Fixing Screws Four screws are supplied as standard accessories. 4. Cable route • When routing cables through the wall/ceiling, drill a hole as shown in the figure. • When routing cables sideway, open the sideway cable exit unscrewing the lid by use of a hexa- gon wrench. Screw the detached lid to the cable access hole on the bottom of the bracket. 5. Waterproof Process When necessary, apply waterproof process to the camera and relevant portions. If you use camera fixing screws that are locally procured, be sure to apply silicone rubber to the screws. ■ Mounting the Camera ● Disassembly of the camera 1. Remove the dome cover by loosening three tamper-proof screws using the supplied bit. 2. Remove the two red-colored screws provided for transport protection using a Philips screwdriver. 2nd transport protection screw