Panasonic microP2 Handheld AVC-ULTRA HD Camcorder Operating Instructions Basic - Page 161
Mode check display, FUNCTION] screen, AUDIO] screen
View all Panasonic microP2 Handheld AVC-ULTRA HD Camcorder manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 161 highlights
Chapter 7 Display - Screen status display Mode check display The camera settings and status can be displayed on the viewfinder or LCD monitor screen for check. Each time the switch on the camera is pushed towards the side, the five screens are switched. [STATUS] screen display → [FUNCTION] screen display → [AUDIO] screen display → [USER SW] screen display → [META INFO] screen display → no display Each screen is displayed for approximately five seconds. Pushing the switch towards the side while the screen is displayed moves to the next screen. [FUNCTION] screen Displays the video output status and information of the recording media. [SDI OUT] [P2CARD STATUS] [PROXY] [NETWORK] - [TYPE] [CHAR] - [TOTAL P2/mP2] [SLOT1] [SLOT2] [SLOT3] [MEDIA] [MODE] [PROXY ERROR] [NETWORK] Displays the status of the signal output from the terminal. Displays the format of the signal output from the terminal by [HD‑SDI]/ [SD‑SDI]. Displays the superimposition status of characters selected in the main menu → [OUTPUT SEL] → [SDI OUT CHAR] by [ON]/[OFF]. Displays the status of the P2 card inserted in the card slot, remaining capacity, and total used capacity. The statuses of cards to be displayed are as follows: [ACTIVE]/[ACCESSING]/[INFO READING]/[FULL]/[PROTECTED]/[NOT SUPPORTED]/ [FORMAT ERROR]/[AUTH NG]/[REC IMPOSSIBLE]/[NO CARD] For details, refer to "P2 card access LEDs and status of P2 cards" (page 35). Displays the remaining capacity/total capacity totaled for slots 1 and 2 (or slots 3) and the recording media ([P2] or [mP2]). Displays the status of the microP2 memory card in slot 1 and remaining capacity/total capacity. Displays the status of the microP2 memory card in slot 2 and remaining capacity/total capacity. Displays the status of the P2 memory card in slot 3 and remaining capacity/total capacity. Displays the media selection status for proxy recording. [P2]/[P2&SD]/[OFF] Displays the setting status for proxy recording mode. [AVC-G6 2CH MOV]/[SHQ 2CH MOV]/[HQ 2CH MOV]/[LOW 2CH MOV] Displays the operation error on the proxy module. Displays the status of network to be used and streaming status. [AUDIO] screen Displays audio settings and the selection status of each recording channel. [AUDIO] [A.IN] [LEVEL] [F.VR] [LIMITER] [LOWCUT] [INT MIC] [AUDIO OUT] [CH1/2/3/4] [CH1/2/3/4] [CH1/2/3/4] [CH1/2/3/4] [CH1/2/3/4] Displays the built-in microphone status set in the main menu → [AUDIO SETUP] → [INPUT SETTING] → [INT MIC]. ff[STEREO]: Records audio from two directions in the front with the 2ch stereo microphone. ff[MONO]: This mode records clearer audio from the front by enhancing the directionality forward like a shotgun microphone. Audio recorded on the left and right are the same. ff[OFF]: Disables audio of the built-in microphone. Displays the audio input signal status set in the main menu → [AUDIO SETUP] → [OUTPUT SETTING] → [AUDIO OUT]. [CH1/CH2]/[CH1]/[CH2]/[CH3/CH4]/[CH3]/[CH4] Displays the input status of each channel. [INT(L)]/[INT(R)]/[INPUT1]/[INPUT2] Displays the recording level adjustment method currently selected on each channel. ff[VR]: Displayed when manual adjustment using the adjustment dial is set. ff[MENU]: Displayed when manual adjustment using [LEVEL CONTROL CH3]/[LEVEL CONTROL CH4] is set in the main menu → [AUDIO SETUP] → [RECORDING CH SETTING]. ff[AUTO]: Displayed when automatic adjustment is set. Displays by [ON]/[OFF] whether the dial is enabled on the channel to which [VR] (manual adjustment by adjustment dial) is displayed in [LEVEL]. Displays the limiter settings of each channel. Displays the lowcut filter status of each channel. - 161 -