Pentair MasterTemp High Performance Pool and Spa Heaters Heater Wire Harness K
Pentair MasterTemp High Performance Pool and Spa Heaters Manual
 |
View all Pentair MasterTemp High Performance Pool and Spa Heaters manuals
Add to My Manuals
Save this manual to your list of manuals |
Pentair MasterTemp High Performance Pool and Spa Heaters manual content summary:
- Pentair MasterTemp High Performance Pool and Spa Heaters | Heater Wire Harness K - Page 1
SERVICED ONLY BY A QUALIFIED POOL SERVICE PROFESSIONAL. INSTALLERS, POOL OPERATORS AND OWNERS MUST READ THESE WARNINGS AND ALL INSTRUCTIONS IN THE HEATER INSTALLATION AND USER'S GUIDE BEFORE USING THIS PRODUCT. THESE INSTRUCTIONS MUST BE LEFT WITH THE POOL OWNER. Pentair Water Pool and Spa heater - Pentair MasterTemp High Performance Pool and Spa Heaters | Heater Wire Harness K - Page 2
Qty. 466225 WH HRN US W/ FC 1 476226 WH HRN AUSTRALIA W/ FC 1 476204 ADAPT 6 PIN 1 476205 ADAPT 5 PIN FOR AU 1 476209 ADAPT F1-F2 1 476250 INSTALLATION INSTRUCTIONS 1 476212 ADAPT 5 PIN 1 476250 INSTALLATION INSTRUCTIONS 1 P/N 476204 P/N 476209 P/N 476212 2 P/N 476205 - Pentair MasterTemp High Performance Pool and Spa Heaters | Heater Wire Harness K - Page 3
starting: Always disconnect AC power to the heater before proceeding with the wire harness replacement instructions. To replace the wire harness on a MasterTemp® or Max-E-Therm® Heater: 1. MasterTemp Heater: Remove right side panel from the heater (Fig. 1 and Fig. 2). 7. Install wire harness (USA - Pentair MasterTemp High Performance Pool and Spa Heaters | Heater Wire Harness K - Page 4
WIRE HARNESS REPLACEMENT INSTRUCTIONS (USA) 7. Install the bushing in the top of the control box. Use (Fig. (Fig. 7). FIG. 10. 11. Connect the Gas Valve. (Fig. 11). FIG. 7 9. If the heater has a legacy ICM, connect each wire from P/N 476204 wire adapter to its correct location labeled in the ICM. - Pentair MasterTemp High Performance Pool and Spa Heaters | Heater Wire Harness K - Page 5
WIRE HARNESS REPLACEMENT INSTRUCTIONS (USA) 13. Connect the Air Flow Switch. (Fig. 13). 16. Connect F1 and F2 plug into the ICM. If the heater has the legacy 17. Connect 5-pin plug into the ICM from the wire harness. If the heater has the legacy ICM. Connect the 5-pin wire adapter (476212) to the - Pentair MasterTemp High Performance Pool and Spa Heaters | Heater Wire Harness K - Page 6
WIRE HARNESS REPLACEMENT INSTRUCTIONS (USA) 19. Plug in the transformer. (Fig. 19). 22. Connect the Water sensor is located at the top of the manifold. The High Limit switch is located at the bottom of the manifold. (Fig. 21). FIG. 23. 24. If the heater does not have an RS-485 port on the circuit - Pentair MasterTemp High Performance Pool and Spa Heaters | Heater Wire Harness K - Page 7
! Before starting: Always disconnect AC power to the heater before proceeding with the wire harness replacement instructions. To replace the wire harness on a MasterTemp® or Max-ETherm® Heater: 1. MasterTemp Heater: Remove right side panel from the heater (Fig. 1 and Fig. 2). 8. Place the 12-pin - Pentair MasterTemp High Performance Pool and Spa Heaters | Heater Wire Harness K - Page 8
WIRE HARNESS REPLACEMENT INSTRUCTIONS (AUSTRALIA) 10. Route the Red and Green wires into the Control Box through the bottom hole. Plug the Fireman's jumper into the terminal board. Install - Pentair MasterTemp High Performance Pool and Spa Heaters | Heater Wire Harness K - Page 9
WIRE HARNESS REPLACEMENT INSTRUCTIONS (AUSTRALIA) 16. Connect the Red/yellow wire to VAL ¼" tab at Connect the 5-pin plug into the ICM from the new wire harness as shown in fig 17. If the heater has the legacy ICM. Connect the 5-pin wire adapter (476205) to the corresponding terminals in the ICM (s1 - Pentair MasterTemp High Performance Pool and Spa Heaters | Heater Wire Harness K - Page 10
WIRE HARNESS REPLACEMENT INSTRUCTIONS (AUSTRALIA) 22. Mount the bundle on the blower plug in the blower motor. (Fig. 18). 25. Connect the Thermistor sensor and High Limit Switch. Note: The Thermistor sensor is located at the top of the manifold. The High Limit switch is located at the bottom of - Pentair MasterTemp High Performance Pool and Spa Heaters | Heater Wire Harness K - Page 11
INSTRUCTIONS (AUSTRALIA) 27. Plug the harness into the back of the board. (Fig. 23.) 31. Connect the Gas Valve. (Fig. 26.). FIG. 23. 28. If the heater Air Flow Switch. (Fig. 27). FIG. 24. 29. Reassemble the heater control panel assembly. Be sure that the control panel can be adjusted without - Pentair MasterTemp High Performance Pool and Spa Heaters | Heater Wire Harness K - Page 12
NC 27330 • (919) 566-8000 10951 WEST LOS ANGELES AVE., MOORPARK, CA 93021 • (805) 553-5000 Technical Support: 800.831.7133 www.pentair.com All indicated Pentair trademarks and logos are property of Pentair Inc. or its global affiliates in the U.S.A. and/or other countries. Third party registered and
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
1
Pentair Water Pool and Spa heater related products are available at:
Call (800) 831-7133 for additional free copies of these instructions.
FAILURE TO FOLLOW ALL INSTRUCTIONS AND WARNINGS CAN RESULT IN
SERIOUS BODILY
INJURY OR DEATH. THIS PRODUCT SHOULD BE
INSTALLED AND SERVICED ONLY BY A QUALIFIED POOL SERVICE
PROFESSIONAL.
INSTALLERS, POOL OPERATORS AND OWNERS MUST
READ THESE WARNINGS AND ALL INSTRUCTIONS IN THE HEATER
INSTALLATION AND USER’S GUIDE
BEFORE USING THIS PRODUCT.
THESE INSTRUCTIONS MUST BE LEFT WITH THE POOL OWNER.
INSTALLATION INSTRUCTIONS
WIRE HARNESS REPLACEMENT KIT
USA (P/N 461107) AND AUSTRALIA (P/N 461108)
FOR MASTERTEMP® AND MAX-E-THERM® POOL AND SPA HEATERS
READ AND FOLLOW ALL INSTRUCTIONS - SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Wire harness Instructions for USA and Australian heater models
The following instructions describe how to replace the wire harness in a MasterTemp or Sta-Rite pool
and spa heater (USA and Australia models) that doesn’t have RS-485 communication capability and
a legacy Ignition Control Module.
If you do not know what Ignition Control Module is installed, please
contact customer service at 800.831.7133.
P/N 476250.A
9/2020
Contents
Wire Harness Replacement (USA) page 3-6
Wire Harness Replacement (Australia) page 7-11