Philips AJL308 User manual - Page 4

Power supply/Basic operation Alarm Power supply • Connect the supplied power adapter to the set's DC 9V socket and to the power socket. Helpful hints: To avoid damage to the set, use only the adapter supplied! The type plate is located on the bottom of the set. Setting OSD (On Screen Display) language 1 Press MENU. ➜The menu appears. 2 Press 1 2 to highlight "General". 3 Press 4 to highlight "Language". 4 Press 1 2 to select desired language. 5 After finishing the setting, press CLOCK, TUNER, PHOTO/VIDEO or MUSIC to exit the setup menu. Setting time and date To change time format 1 In the Clock menu, press 3 4 to select the value of "12/24 Hour Format". 2 Press 1 2 to toggle between 12H and 24H. Note: When the set is disconnected from the power outlet for about 5 minutes, you need to reset the time and date. Setting and activating alarm You can set two different alarm times. 1 Press CLOCK. 2 Press and hold ALARM 1 or ALARM 2. ➜The hour digits flash. 3 Press or hold down 3 4 to set hour. 4 Press ALARM 1 or ALARM 2 to confirm. ➜The minute digits flash. 5 Press or hold down 3 4 to set minute. 6 Press ALARM 1 or ALARM 2 to confirm. 7 Press again ALARM 1 or ALARM 2 to activate alarm setting. ➜When alarm is activated, is displayed. ➜At the set alarm time, the alarm will sound and its volume will increase gradually. Selecting alarm mode 1 Press MENU. ➜The menu appears. 2 Use 1 2 to highlight "Clock". 3 Press 3 4 to select "Alarm Music". 4 Press 1 2 to select specific music you like. ➜Alarm will go off with the music you select. 1 Press CLOCK. 2 Use MENU. 3 Use 3 4 1 2 to select a field of "Time Set" and "Date (Year-Month-Day)". 4 Press OK to confirm. 5 Press or hold down 3 4 to set the values. 6 Press OK to confirm. 7 Repeat Steps 3-6 to set other values of "Time Set and "Date (Year-Month-Day)". 8 After finishing the setting, press CLOCK, TUNER, PHOTO/VIDEO or MUSIC to exit the setup menu. Switching off the alarm There are three ways of switching off the alarm. Unless you choose to cancel the alarm completely, the DAILY ALARM RESET option will be automatically kept activated from the time your alarm first goes off. call at the same time for the following day: Daily alarm reset If you want the alarm to be stopped immediately but also wish to repeat the alarm Digital tuner • During the alarm call, press ALARM 1 or ALARM 2. ➜ is displayed. Repeat alarm This will repeat your alarm call at 9-minute intervals. • During the alarm call, press REPEAT ALARM / BRIGHTNESS CONTROL. ➜ flashes. Switching off the alarm completely • Press repeatedly ALARM 1 or ALARM 2 until is changed to . ➜When alarm is deactivated, is dispalyed. Helpful hints: During alarm call, if no button is pressed, alarm call will last 30 minutes. Tuner Tuning to radio station 1 Press TUNER to switch on radio (FM only). 2 Press and hold 1 2 for about 2 seconds, then release. ➜The radio automatically tunes to a station of sufficient reception. 3 Repeat step 2 if necessary until you find the desired station. • To tune to a weak station, press 1 2 briefly and repeatedly until you have found optimal reception. Turning on/off radio • To turn off radio, press OK.To turn on radio, press OK again. To improve reception: FM: Extend and adjust the pigtail for optimum reception. Programming radio stations You can store up to a total of 20 FM radio stations in the memory, manually or automatically (Auto store). Manual programming 1 Tune to your desired station (See "Tuning to radio station"). 2 Press and hold TUNER for about 2 sec- onds, then release. ➜Preset number will flash. 3 Press 34 once or more to allocate a number from 1 to 20. ➜Preset number will flash. 4 Press TUNER again to confirm. 5 Repeat steps 1-4 to store other stations. Note: - You can erase a preset station by storing another frequency in its place. Auto store Autostore automatically starts programming radio stations from preset 1. Any previous presets e.g. manually programmed will be erased. 1 In TUNER mode, press MENU to display tuner menu. 2 Press 4 to select "Tuner Auto Program". 3 Press OK. ➜Available stations are programmed (FM). After all stations are stored, the first autostore preset station will then automatically play. To listen to a preset or autostore station Press 34 once or more until the desired preset station is displayed.