Philips BDL3215E User manual - Page 17

Setup Procedure - touch

Get Philips BDL3215E PDF manuals and user guides
UPC - 685417500284
View all Philips BDL3215E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Setup Procedure 1. Install the system on the right location CAUTION: ‡ THE LCD MONITOR MUST BE MOVED OR INSTALLED BY TWO OR MORE PERSONS. (For 42" only) Failure to follow this caution may result in injury if the LCD monitor falls. ‡ DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY YOURSELF. 7KH/&'GLVSOD\PXVWEHLQVWDOOHGE\DTXDOLÀHGWHFKQLFLDQ Contact your dealer for more information. ‡ DO NOT MOUNT OR OPERATE THE DISPLAY UPSIDE DOWN, FACE UP, OR FACE DOWN. ‡ DO NOT INSTALL THE LCD MONITOR WHERE IT WILL BE EXPOSED TO DIRECT SUNLIGHT. Failure to follow this caution will result in display defects. IMPORTANT: Lay the protective sheet, which was wrapped around the LCD monitor when it was packaged, beneath the LCD monitor so as not to scratch the panel. 2. Install the remote control batteries The remote control is powered by 1.5V AAA batteries. To install or replace batteries: 1. Press and slide to open the cover. 2. Align the batteries according to the (+) and (-) indications inside the case. 3. Replace the cover. CAUTION: Incorrect use of batteries can result in leaks or bursting. Be careful especially about the following points. ‡ Place "AAA" batteries matching the + and - signs on each battery to the + and - signs of the battery compartment. ‡ 'RQRWPL[EDWWHU\W\SHV ‡ Do not combine new batteries with used ones. It causes shorter battery life or leakage of batteries. ‡ 5HPRYHGHDGEDWWHULHVLPPHGLDWHO\WRSUHYHQWEDWWHU\OLTXLG from leaking into the battery compartment. Don't touch H[SRVHGEDWWHU\DFLGLWFDXVHGDPDJHWR\RXUVNLQ NOTE: If you do not intend to use the Remote Control for a long period, remove the batteries. User Manual BDL3215E / BDL4225E 3. Connect to external equipment ‡ 7RSURWHFWWKHFRQQHFWHGHTXLSPHQWWXUQRIIWKHPDLQSRZHU before making connections. ‡ Please refer to section "Connectivity" P.17~P.21 for operations. 4. Connect power cord ‡ The power outlet socket should be installed as near to the HTXLSPHQWDVSRVVLEOHDQGVKRXOGEHHDVLO\DFFHVVLEOH ‡ Fully insert the prongs into the power outlet socket. Loose connection may cause noise. NOTE: Please refer to "SAFETY INSTRUCTIONS" section of this manual for proper selection of AC power cord. 5. Turn on the power of the attached external equipment When connected with a computer, turn the computer power RQÀUVW 6. Operate the attached external equipment 'LVSOD\WKHVLJQDOIURPWKHH[WHUQDOHTXLSPHQW 7. Adjust the sound 0DNHDGMXVWPHQWVWRGHFUHDVHRULQFUHDVHYROXPHLIUHTXLUHG 8. Adjust the screen 0DNHDGMXVWPHQWVWRWKHGLVSOD\SRVLWLRQRUVHWWLQJVLIUHTXLUHG 9. Adjust the image 0DNHDGMXVWPHQWVRIEULJKWQHVVRUFRQWUDVWLIUHTXLUHG 10.Recommended Adjustment To reduce the risk of "image persistence", please adjust the following items based on the application being used: "POWER SAVE", "PANEL SAVING", "DATE AND TIME", "SCHEDULE". 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
User Manual BDL3215E / BDL4225E
14
Setup Procedure
Install the system on the right location
1.
CAUTION:
THE LCD MONITOR MUST BE MOVED OR INSTALLED BY
TWO OR MORE PERSONS. (For 42” only)
Failure to follow this caution may result in injury if the LCD
monitor falls.
DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY
YOURSELF.
Contact your dealer for more information.
DO NOT MOUNT OR OPERATE THE DISPLAY UPSIDE
DOWN, FACE UP, OR FACE DOWN.
DO NOT INSTALL THE LCD MONITOR WHERE IT WILL BE
EXPOSED TO DIRECT SUNLIGHT.
Failure to follow this caution will result in display defects.
IMPORTANT:
Lay the protective sheet, which was wrapped around the LCD
monitor when it was packaged, beneath the LCD monitor so as
not to scratch the panel.
Install the remote control batteries
2.
The remote control is powered by 1.5V AAA batteries. To
install or replace batteries:
Press and slide to open the cover.
1.
Align the batteries according to the (+) and (–) indications
2.
inside the case.
Replace the cover.
3.
CAUTION:
Incorrect use of batteries can result in leaks or bursting. Be
careful especially about the following points.
Place “AAA” batteries matching the + and - signs on each
battery to the + and - signs of the battery compartment.
Do not combine new batteries with used ones.
It causes
shorter battery life or leakage of batteries.
from leaking into the battery compartment. Don’t touch
NOTE:
If you do not intend to use the Remote Control for a long period,
remove the batteries.
Connect to external equipment
3.
before making connections.
Please refer to section “Connectivity” P.17~P.21 for operations.
Connect power cord
4.
The power outlet socket should be installed as near to the
Fully insert the prongs into the power outlet socket. Loose
connection may cause noise.
NOTE:
Please refer to “SAFETY INSTRUCTIONS” section of this
manual for proper selection of AC power cord.
Turn on the power of the
5.
attached external equipment
When connected with a computer, turn the computer power
Operate the attached external equipment
6.
Adjust the sound
7.
Adjust the screen
8.
Adjust the image
9.
Recommended Adjustment
10.
To reduce the risk of “image persistence”, please adjust the
following items based on the application being used:
“POWER SAVE”, “PANEL SAVING”, “DATE AND TIME”,
“SCHEDULE”.