Philips DVD972CH98 User manual - Page 14

Dolby Digital/pcm, Stream/pcm

Page 14 highlights

- Progressive Scan (Y PR/CR PB/CB connection only) Progressive Scan Video provides the highest quality pictures with less flickering. If you are using the Component Video jacks, but are connecting the DVD Player to a standard (analog) television, set Progressive Scan to Off. If you are using the Component Video jacks for connection to a TV or monitor that is compatible with a progressive scan signal, set Progressive Scan to On. Notes: - Progressive Scan only works when the VIDEO OUTPUT switch on the rear panel is set to COMPONENT/ PROGRESSIVE SCAN. - Make sure the TV's Sync Mode setting is correct. For example, on some Philips TVs, set "SYNC MODE" to "SYNC MODE 2." An incorrect Sync Mode setting will cause the picture to shift off-center on the TV screen while using Progressive Scan. Check your TV owner's manual for details on correct Sync Mode settings. Caution: - Once the setting for progressive scan output is entered, an image will only be visible on a progressive scan compatible TV or monitor. If you set Progressive Scan to On in error, you must reset the unit. Press STOP to stop any disc that is playing. Next, press STOP again and hold it for five seconds before releasing it.The video output will be restored to the standard setting, and a picture will once again be visible on a conventional analog TV or monitor. Disc Audio Off Disc Subtitle On Disc Menu Rating Password TV Aspect Menu Language Progressive Scan Digital Audio Output 5.1 Speaker Setup Others Sound - Digital Audio Output Each DVD disc has a variety of audio output options. Set the player's Digital Audio Output according to the type of audio system you use. DOLBY DIGITAL/PCM: Select "DOLBY DIGITAL/ PCM" if you connected the DVD Player's DIGITAL OUT jack to a Dolby Digital decoder (or an amplifier or other equipment with a Dolby Digital decoder). Stream/PCM: Select "Stream/PCM" if you connected the DVD Player's DIGITAL OUT jack to an amplifier or other equipment with a DTS decoder, Dolby Digital decoder or MPEG decoder. PCM: Select "PCM" if you connected the DVD Player's DIGITAL OUT jack to an amplifier or other equipment with linear PCM only (or Mini Disc (MD) recorder or Digital Audio Tape (DAT) deck). Disc Audio Disc Subtitle Disc Menu Rating Password TV Aspect Menu Language Progressive Scan Digital Audio Output 5.1 Speaker Setup Others /PCM DOLBY DIGITAL Stream/PCM PCM Sample Freq. 48 KHz 96KHz - Sample Frequency To change the Sample Frequency setting, first select the desired Digital Audio Output as indicated at left. If your receiver or amplifier is NOT capable of handling 96KHz signals, select 48KHz.When this choice is made, this unit will automatically convert any 96KHz signals to 48KHz so your system can decode them. If your receiver or amplifier is capable of handling 96KHz signals, select 96KHz.When this choice is made, this unit will pass each type of signal through without any further processing. - 5.1 Speaker settings Select speaker settings, including volume balance and delay time, or test the speaker settings. Speaker settings are only active on the Analog MultiChannel Output. (See appendix, page 24.) Disc Audio Disc Subtitle Disc Menu Rating Password TV Aspect Menu Language Progressive Scan Digital Audio Output 5.1 Speaker Setup Others R R Front L Volume Size Delay Test Return 0 dB Large 0 ms 14 PREPARATION

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

14
Progressive Scan (Y P
R
/C
R
P
B
/C
B
connection only)
Progressive Scan Video provides the highest quality pictures
with less flickering.
If you are using the Component Video jacks, but are
connecting the DVD Player to a standard (analog)
television, set Progressive Scan to Off.
If you are using the Component Video jacks for connection
to a TV or monitor that is compatible with a progressive
scan signal, set Progressive Scan to On.
Notes:
Progressive Scan only works when the VIDEO OUTPUT
switch on the rear panel is set to COMPONENT/
PROGRESSIVE SCAN.
Make sure the TV’s Sync Mode setting is correct. For
example, on some Philips TVs, set “SYNC MODE” to “SYNC
MODE 2.” An incorrect Sync Mode setting will cause the
picture to shift off-center on the TV screen while using
Progressive Scan. Check your TV owner’s manual for details on
correct Sync Mode settings.
Caution:
Once the setting for progressive scan output is entered, an
image will only be visible on a progressive scan compatible TV or
monitor. If you set Progressive Scan to On in error, you must reset
the unit. Press STOP to stop any disc that is playing. Next, press
STOP again and hold it for five seconds before releasing it.The
video output will be restored to the standard setting, and a
picture will once again be visible on a conventional analog TV or
monitor.
Disc Subtitle
Disc Menu
Rating
Password
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Others
Disc Audio
Off
On
Sound
Digital Audio Output
Each DVD disc has a variety of audio output options. Set
the player
s Digital Audio Output according to the type of
audio system you use.
DOLBY DIGITAL/PCM
: Select
DOLBY DIGITAL/ PCM
if
you connected the DVD Player
s DIGITAL OUT jack to a
Dolby Digital decoder (or an amplifier or other equipment
with a Dolby Digital decoder).
Stream/PCM
: Select
Stream/PCM
if you connected the
DVD Player
s DIGITAL OUT jack to an amplifier or other
equipment with a DTS decoder, Dolby Digital decoder or
MPEG decoder.
PCM
: Select
PCM
if you connected the DVD Player
s
DIGITAL OUT jack to an amplifier or other equipment with
linear PCM only (or Mini Disc (MD) recorder or Digital
Audio Tape (DAT) deck).
Disc Subtitle
Disc Menu
Rating
Password
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Others
Disc Audio
DOLBY
DIGITAL
/PCM
Stream/PCM
PCM
Sample Freq.
48 KHz
96KHz
Sample Frequency
To change the Sample Frequency setting, first select the
desired Digital Audio Output as indicated at left.
If your receiver or amplifier is NOT capable of handling
96KHz signals, select 48KHz. When this choice is made, this
unit will automatically convert any 96KHz signals to 48KHz
so your system can decode them.
If your receiver or amplifier is capable of handling 96KHz
signals, select 96KHz. When this choice is made, this unit will
pass each type of signal through without any further
processing.
5.1 Speaker settings
Select speaker settings, including volume balance and delay
time, or test the speaker settings.
Speaker settings are only active on the Analog Multi-
Channel Output. (See appendix, page 24.)
Disc Subtitle
Disc Menu
Rating
Password
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Others
Disc Audio
Front L
Volume
0 dB
Size
Large
Delay
0 ms
Test
Return
R
R
P
REPARATION