Philips MCD708 User manual - Page 19

Getting Started - user manual

Get Philips MCD708 PDF manuals and user guides
UPC - 609585114524
View all Philips MCD708 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

English Getting Started Step 1: Inserting batteries into the Remote Control 3 1 2 1 Open the battery compartment. 2 Insert two AAA batteries following the indications (+/-) inside the compartment. 3 Close the cover. Using the Remote Control to operate the Player 1 Aim the Remote Control directly at the remote sensor (IR) on the front panel. 2 Do not put any objects between the Remote Control and the DVD Player while operating the DVD Player. CAUTION! - Remove batteries if they are exhausted or if the Remote Control is not being used for a long time. - Do not use old and new or different types of batteries in combination. - Batteries contain chemical substances, so they should be disposed of properly. Step 2: Setting up the TV IMPORTANT! Make sure you have completed all the necessary connections. (See "Connecting TV"). 1 Switch the DVD system on and then select DISC source. (See "Switching the system on/off"). 2 Turn on the TV and set to the correct video-in channel.You should see the blue Philips DVD background screen on the TV. ➜ Usually these channels are between the lowest and highest channels and may be called FRONT, A/V IN, or VIDEO. See your TV manual for more details. ➜ Or, you may go to channel 1 on your TV, then press the Channel down button repeatedly until you see the Video In channel. ➜ Or, the TV Remote Control may have a button or switch that chooses different video modes. ➜ Or, set the TV to channel 3 or 4 if you are using an RF modulator. Setting up Progressive Scan feature (for Progressive Scan TV only) The progressive scan display twice the number of frames per seconds than interlaced scanning (ordinary normal TV system).With nearly double the number of lines, progressive scan offers higher picture resolution and quality. IMPORTANT! Before enabling the progressive scan feature, you must ensure: 1) Your TV can accept progressive signals, a progressive scan TV is required. 2) You have connected the DVD player to your TV using Y Pb Pr (see "Connections-Step 5: Connecting TV- Using Component Video jacks".) 1 Turn on your TV. 2 Turn off your TV progressive scan mode or turn on interlaced mode (refer to your TV user manual). 3 Press ECO POWER/STANDBY-ON B (B on the remote) to turn on the DVD player. 4 Select the correct Video Input channel. ➜ The DVD background screen appears on the TV. 5 Press SYSTEM. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
19
English
Step 1:
Inserting batteries into
the Remote Control
1
3
2
1
Open the battery compartment.
2
Insert two AAA batteries following the
indications (+/-) inside the compartment.
3
Close the cover.
Using the Remote Control to operate
the Player
1
Aim the Remote Control
directly at the remote sensor
(IR) on the front panel.
2
Do not put any objects
between the Remote Control
and the DVD Player while
operating the DVD Player.
CAUTION!
–
Remove batteries if
they are exhausted or if the Remote
Control is not being used for a long time.
–
Do not use old and new or different
types of batteries in combination.
–
Batteries contain chemical substances,
so they should be disposed of properly.
Step 2:
Setting up the TV
IMPORTANT!
Make sure you have completed all the
necessary connections. (See
“Connecting TV”).
1
Switch the DVD system on and then select DISC
source. (See “
Switching the system on/off
”).
2
Turn on the TV and set to the correct video-in
channel.You should see the blue Philips DVD
background screen on the TV.
➜
Usually these channels are between the
lowest and highest channels and may be called
FRONT, A/V IN, or VIDEO. See your TV manual
for more details.
➜
Or, you may go to channel 1 on your TV, then
press the Channel down button repeatedly until
you see the Video In channel.
➜
Or, the TV Remote Control may have a
button or switch that chooses different video
modes.
➜
Or, set the TV to channel 3 or 4 if you are
using an RF modulator.
Setting up Progressive Scan feature (for
Progressive Scan TV only)
The progressive scan display twice the number
of frames per seconds than interlaced scanning
(ordinary normal TV system). With nearly double
the number of lines, progressive scan offers
higher picture resolution and quality.
IMPORTANT!
Before enabling the progressive scan
feature, you must ensure:
1) Your TV can accept progressive signals, a
progressive scan TV is required.
2) You have connected the DVD player to your
TV using Y Pb Pr (see “Connections-Step 5:
Connecting TV- Using Component Video jacks”.)
1
Turn on your TV.
2
Turn off your TV progressive scan mode or turn
on interlaced mode (refer to your TV user
manual).
3
Press
ECO POWER/STANDBY-ON
B
(
B
on the remote) to turn on the DVD player.
4
Select the correct Video Input channel.
➜
The DVD background screen appears on the
TV.
5
Press
SYSTEM
.
Getting Started