Philips MVR450MG Owners Manual - Page 11

Turning on Your VCR

Get Philips MVR450MG PDF manuals and user guides View all Philips MVR450MG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Turning on Your VCR 11 q Before turning on your VCR, make sure batteries are in the remote and the VCR and TV are connected (see pages 5-10). q You cannot set up channels if you are using a Cable Box/Satellite. q The instructions on this page only work when you turn on the VCR for the first time. If there is a power failure or if the VCR is unplugged for more than 30 seconds, repeat this procedure. 2 Turn on the TV. 1 Press POWER. The POWER light and the VCR/TV light will appear. POWER VCR/TV EJECT 2 Turn on the TV. Set it to the same channel as the RF output channel of the VCR (see page seven). If you connected the VCR to a TV using Audio/Video cables, choose the A/V In or Auxiliary In or Line Input channel at the TV.The menu shown below will appear. LANGUAGE SELECT B ENGLISH [ON] FRANCAIS ESPAÑOL REW PLAY STOP F.FWD MENU STATUS CLEAR 1 2 3 4 5 6 CH 7 8 9 0 SPEED SEARCH MODE STILL/PAUSE PUSH F. FWD REC MEMORY SLOW 1 3-5 3 Press PLAY or STOP to select ENGLISH, FRANCAIS or ESPAÑOL. [ON] will appear beside your choice. 4 Press F.FWD. AUTO SET UP will appear on the screen. AUTO SET UP PUSH F. FWD 5 Press F.FWD to begin automatic channel setup. AUTO SET UP will flash on the screen and channels will count up on the screen as setup progresses.When channels are set up, the VCR will go to the lowest channel available. The VCR will memorize all available channels, so when you use CH to change TV channels at the VCR, you'll only scan through channels you receive. Helpful Hints • If you do not see any displays when you turn on the VCR, check your hookups, then try again. If you still do not see any displays, follow the steps under "Automatic Channel Setup" on page 12 and "Language Selection" on page 16. • If you try to set up channels when there is no antenna or cable connected to the VCR, programming will appear to take place. Eventually,AUTO SET UP will appear on the screen steadily, and channel programming will stop. Connect an antenna or cable to the ANT(enna) IN jack of the VCR, then press F.FWD again. Channel programming will begin again. • To stop channel setup, press CLEAR.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
CH
3
2
1
6
5
4
9
8
7
0
POWER
STATUS
SLOW
REC
MEMORY
SPEED
SEARCH MODE
STILL/PAUSE
VCR/TV
EJECT
MENU
CLEAR
REW
PLAY
STOP
F.FWD
Turning on Your VCR
11
●
Before turning on your VCR, make sure batteries are in the
remote and the VCR and TV are connected (see pages 5-10).
●
You cannot set up channels if you are using a Cable Box/Satellite.
●
The instructions on this page only work when you turn on the
VCR for the first time. If there is a power failure or if the VCR is
unplugged for more than 30 seconds, repeat this procedure.
1
Press POWER.
The POWER light and the VCR/TV light
will appear.
2
Turn on the TV.Set it to the same channel as the RF
output channel of the VCR (see page seven).
If you
connected the VCR to a TV using Audio/Video cables, choose
the A/V In or Auxiliary In or Line Input channel at the TV.The
menu shown below will appear.
2
1
Turn on the TV.
•
If you do not see any displays
when you turn on the VCR, check
your hookups, then try again.
If
you still do not see any displays,
follow the steps under
“
Automatic
Channel Setup
”
on page 12 and
“
Language Selection
”
on page 16.
•
If you try to set up channels when
there is no antenna or cable con-
nected to the VCR, programming
will appear to take place.
Eventually,AUTO SET UP will
appear on the screen steadily, and
channel programming will stop.
Connect an antenna or cable to
the ANT(enna) IN jack of the VCR,
then press F.FWD again. Channel
programming will begin again.
•
To stop channel setup, press
CLEAR.
Helpful Hints
3-5
LANGUAGE SELECT
B
ENGLISH
[ON]
FRANCAIS
ESPA
Ñ
OL
PUSH F. FWD
3
Press PLAY or STOP to select ENGLISH,FRANCAIS
or ESPA
Ñ
OL.
[ON] will appear beside your choice.
4
Press F.FWD.
AUTO SET UP will appear on the screen.
5
Press F.FWD to begin automatic channel setup.
AUTO SET UP will flash on the screen and channels will
count up on the screen as setup progresses.When channels
are set up, the VCR will go to the lowest channel available.
The VCR will memorize all available channels, so when you
use CH
to change TV channels at the VCR, you
’
ll only
scan through channels you receive.
AUTO SET UP
PUSH F. FWD