Pioneer AXM-P8000 Other Manual - Page 1

INSTALLATION MANUAL OF OF AXM-P8000 This product conforms to CEMA cord colors. Le code de couleur des câbles utilisé pour ce produit est conforme à CEMA. Printed in Japan UC N STAR N STAR MANUEL D'INSTALLATION Installation Note: • Before finally installing the unit, connect the wiring temporarily, making sure it is all connected up properly, and the unit and the system work properly. • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. • Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. • Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop. 3. Attach the display unit to dashboard or console. Tapping screw Double faced tape Dashboard or console Installing the display unit Installation using the bracket 1. Attach bracket (A) to the display unit. Display unit Drill 2 to 2.5 mm diameter holes. Installation using Velcro tape • Thoroughly wipe off the surface before affixing the velcro tape. 1. Affix the velcro tape (rough surface) to the display unit. Display unit Bracket (A) Screw 2. Attach bracket (B). Velcro tape (rough surface) 2. Attach the display unit to dashboard or console. Binding screw Washer Bracket (B) Dashboard or console Velcro tape (soft surface) Installation using the double faced tape • Thoroughly wipe off the surface before affixing the double faced tape. Dashboard or console Installing the hide-away unit Installation using Velcro tape • Thoroughly wipe off the surface before affixing the velcro tape. Hide-away unit Double faced tape Display unit Velcro tape Car mat or chassis Connecting the Units Note: • This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the battery voltage. • To avoid shorts in the electrical system, be sure to disconnect the ≠ battery cable before beginning installation. • Refer to the owner's manual for details on connecting the power amp and other units, then make connections correctly. • Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts. • Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body. • Don't pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short. • Do not shorten any leads. If you do, the protection circuit may fail to work when it should. • Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating. • When replacing fuse, be sure to use only fuse of the rating prescribed on the fuse holder. • To avoid short-circuiting, cover the disconnected lead with insulating tape. Especially, insulate the unused speaker leads without fail. There is a possibility of short-circuiting if the leads are not insulated. • To prevent incorrect connection, the input side of the IP-BUS connector is blue, and the output side is black. Connect the connectors of the same colors correctly. • If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be connected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehicle battery may be drained when you are away from the vehicle for several hours. F ACC O F O T T ACC position No ACC position • The black lead is ground. Please ground this lead separately from the ground of high-current products such as power amps. If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire. • Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect cords that have the same function.