Pioneer BDP-09FD Owner's Manual - Page 66
HDMI Color Space
UPC - 012562902364
View all Pioneer BDP-09FD manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 66 highlights
07 66 En Problem Check No picture is displayed or the Is the video cable properly connected? picture is not displayed properly. Is the video cable damaged? Is the input setting on the connected TV or AV receiver or amplifier right? Are you viewing the picture from the video output terminal selected with VIDEO SELECT? Is the output video resolution properly set? • Is the player connected with an HDMI cable other than a High Speed HDMI™ cable (with a Standard HDMI™ cable)? • Are you using an HDMI cable with built-in equalizer? Is Pure Audio set to Mode 1? Is a DVI device connected? Is HDMI Color Space properly set? Picture freezes and the front panel and remote control buttons stop working. Motion is unnatural or picture is not clear. Is the output video resolution set to 1080/24p? No picture is displayed or picture is not output in high definition when playing BDs. • Picture is disturbed during playback. • Picture is dark. • Picture is stretched. • Picture is cropped. • Aspect ratio cannot be switched. Is the TV's aspect ratio properly set? Is TV Aspect Ratio properly set? Is 4:3 Video Out properly set? Is DVD 16:9 Video Out properly set? Picture is interrupted. Is Anamorphic Zoom set to On? Remedy • Connect the cable properly according to the connected devices (page 15). • Insert the cable firmly and all the way in. If the cable is damaged, replace it with a new one. Read the operating instructions of the connected components and switch to the proper input. Press VIDEO SELECT to switch the video output terminal to be viewed (page 25). If Pure Audio is set to Mode 2, video signals are only output from the selected output terminal (page 53). Use OUTPUT RESOLUTION to switch to a resolution at which the video and audio signals are output (page 25). 1080p or Deep Color video signals may not be output properly, depending on the HDMI cable being used or the player's settings. Press while pressing on the player's front panel to restore the video outputs to the factory default settings. After this, if you wish to output the video signals with 1080p or Deep Color, connect the TV using a High Speed HDMI™ cable without built-in equalizer, then reset the player using the Setup Navigator (page 21). When set to Mode 1, no picture is displayed during playback (page 53). The picture may not be displayed properly if a DVI device is connected. Change the HDMI Color Space setting (page 45). • Press STOP to stop playback, then restart playback. • If the playback cannot be stopped, press STANDBY/ON on the player's front panel to turn off the power, then turn the power back on. • If the power cannot be turned off, press and hold STANDBY/ON on the player's front panel for over 5 seconds. The power will turn off. • The picture may not be displayed properly, depending on the source. Set the resolution to something other than 1080/24p. • Change the Pure Cinema setting (page 40). With some discs, it may not be possible to output the video signals from the VIDEO output terminals, the S-VIDEO output terminal or the COMPONENT VIDEO output terminals. In this case, connect using an HDMI cable (page 15). • This player supports Macrovision analog copy protection technology. With some TVs (such as with built-in video deck), the picture will not be displayed properly when the copy protected DVD title is played. This is not a malfunction. • If the player and TV are connected via a DVD recorder/video deck, etc., the picture will not be displayed properly due to analog copy protection. Connect the player and TV directly. Read the TV's operating instructions and set the TV's aspect ratio properly. Set TV Aspect Ratio properly (page 44). Set 4:3 Video Out properly (page 44). Set DVD 16:9 Video Out properly (page 44). When video signals with a resolution of 1080/24p, 1080/60i, 1080/60p or 720/60p are being output from the HDMI OUT terminals or the COMPONENT VIDEO output terminals, they may be output with an aspect ratio of 16:9 even if TV Aspect Ratio is set to 4:3 (Standard) (page 44). Set Anamorphic Zoom to Off (page 52). The picture may be interrupted when the resolution of the recorded video signal switches. Press OUTPUT RESOLUTION to select a setting other than Auto, 1080/24p or Source Direct (page 25).