Pioneer BDP-V6000 Owner's Manual - Page 24
Operating the TV with, the player's remote, control
UPC - 012562957227
View all Pioneer BDP-V6000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 24 highlights
04 - When connecting using component video cables 10 Output test tones. or a video cable to watch the picture, connect to an Use / to select Yes, then press ENTER. AV receiver or amplifier, or a TV using either analog audio cables (7.1 channels or 2 channels), an optical digital audio cable (page 21). 11 Finish the Setup Navigator menu. Use / to select Finish, then press ENTER. - To listen to audio with the player connected to an To redo the settings from the start, select Go Back. AV receiver or amplifier with an HDMI cable, Depending on the output terminal setting of step 4 or the connect the TV to the AV receiver or amplifier using HDMI cable being used, it may happen that no picture an HDMI cable (page 20). and/or sound is output. If this happens, the setup returns • When HDMI or DIGITAL AUDIO is selected at Audio, linear PCM audio signals (2 channels) are output from all terminals other than the ones selected at to step 4 if there is no operation for over 30 seconds. Once the setup returns to step 4, redo the settings according to the connected devices and the HDMI cable being used. Audio. 12 Checking the picture quality settings or setting • When ANALOG AUDIO is selected at Audio, no the picture quality. audio signals are output from the HDMI OUT or If a Pioneer Flat Panel TV or projector is connected to the DIGITAL OUT terminals. player and HDMI is selected for Video in step 4, the player sets the picture quality automatically. The For steps 5 to 8, the step to which you should automatic picture quality setting screen appears. Press proceed depends on the combination of the Video ENTER. and Audio settings. When the automatic picture quality setting screen does 5 Select and set the HDMI High Speed Transmission setting for the HDMI OUT terminal. Use / to select, then press ENTER. not appear, the manual picture quality setting screen appears. Use / to select the connected component, then press ENTER. When HDMI High Speed Transmission for the HDMI OUT terminal is set to On, use a High Speed HDMI™ cable. The picture and sound may not be output properly if any other HDMI cable (for example a standard HDMI™ cable) or an HDMI cable with built-in equalizer is used. 6 Select the output video resolution from the COMPONENT VIDEO output terminals. Use / to select, then press ENTER. For details on the resolution settings, see Switching the output video resolution on page 27. 7 Select the aspect ratio of your TV. Use / to select, then press ENTER. 8 Select the PQLS. Use / to select, then press ENTER. Note Operating the TV with the player's remote control When the manufacturer code for your brand of TV is set on the player's remote control, the TV can be operated using the player's remote control. Caution • For some models it may not be possible to operate the TV with the player's remote control, even for TVs of brands listed on the manufacturer code list. • The settings may be restored to the factory defaults when batteries are replaced. If this happens, set up the settings again. • Only when a Pioneer AV receiver or amplifier is connected , PQLS Screen appears. • The PQLS function works when linear PCM audio signals are output. Therefore the linear PCM audio signals obtained by decoding all audio signals are output from HDMI OUT terminal. For details, see About the audio output settings on page 52. STANDBY/ON OPEN/CLOSE TV CONTROL INPUT SELECT CH VOL AUDIO SUBTITLE ANGLE FL DIMMER • When Use is select, the player is set to the settings below. HDMI Audio Out: PCM KURO LINK: On PQLS: Auto CLEAR AUDIO VIDEO ENTER OUTPUT RESOLUTION • For details on the PQLS function, About PQLS function on page 19. 1 Input the 2-digit manufacturer code. 9 Check the settings. Select Proceed, then press ENTER. 24 Press the number buttons (0 to 9) to input the code while pressing TV CONTROL . En