Pioneer DEH-2700 Operation Manual - Page 15

Adjusting initial settings, Setting the FM tuning step, Switching Auto PI Seek, Saving the battery, - installation

Get Pioneer DEH-2700 PDF manuals and user guides View all Pioneer DEH-2700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Initial Settings Section 08 English Adjusting initial settings 2 Press c or d to select the FM tuning step. Press c to select 50 (50 kHz). Press d to select 100 (100 kHz). 1 Initial settings lets you perform initial setup of different settings for this unit. 1 Function display Shows the function status. 1 Press SOURCE and hold until the unit turns off. 2 Press SOURCE and hold until FM appears in the display. 3 Press AUDIO to display the function names. Press AUDIO repeatedly to switch between the following settings: FM (FM tuning step)A-PI (Auto PI Seek) SAVE (Power save) Use the following instructions to operate each particular setting. # To cancel initial settings, press BAND. # You can also cancel initial settings by holding down SOURCE until the unit turns off. Setting the FM tuning step Normally the FM tuning step employed by seek tuning is 50 kHz. When AF or TA is on, the tuning step automatically changes to 100 kHz. It may be preferable to set the tuning step to 50 kHz when AF is on. ! The tuning step remains at 50 kHz during manual tuning. 1 Press AUDIO to select FM. Switching Auto PI Seek The unit can automatically search for a different station with the same programming, even during preset recall. 1 Press AUDIO to select A-PI. 2 Press a or b to turn the Auto PI seek on or off. Saving the battery consumption It is possible to save the battery consumption when this unit is turned off. After one minute of turning off this unit, this unit will be switched into power save mode. ! You cannot insert and eject a disc while this unit is in power save mode. ! You can only use SOURCE while this unit is in power save mode. Important When you disconnect a battery in order to replace it, this mode is turned off. When installing this unit in a vehicle that does not have an ACC (accessory) position on the ignition switch, the vehicle battery may be drained depending on a connection method. After checking the connection method, turn this mode on if needed. 1 Press AUDIO to select SAVE. 2 Press a or b to turn power save on or off. En 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Adjusting initial settings
1
Initial settings lets you perform initial setup of
different settings for this unit.
1
Function display
Shows the function status.
1
Press SOURCE and hold until the unit
turns off.
2
Press SOURCE and hold until FM ap-
pears in the display.
3
Press AUDIO to display the function
names.
Press
AUDIO
repeatedly to switch between
the following settings:
FM
(FM tuning step)
²
A-PI
(Auto PI Seek)
²
SAVE
(Power save)
Use the following instructions to operate each
particular setting.
#
To cancel initial settings, press
BAND
.
#
You can also cancel initial settings by holding
down
SOURCE
until the unit turns off.
Setting the FM tuning step
Normally the FM tuning step employed by
seek tuning is 50 kHz. When AF or TA is on,
the tuning step automatically changes to 100
kHz. It may be preferable to set the tuning step
to 50 kHz when AF is on.
!
The tuning step remains at 50 kHz during
manual tuning.
1
Press AUDIO to select FM.
2
Press
c
or
d
to select the FM tuning
step.
Press
c
to select
50
(50 kHz). Press
d
to se-
lect
100
(100 kHz).
Switching Auto PI Seek
The unit can automatically search for a differ-
ent station with the same programming, even
during preset recall.
1
Press AUDIO to select A-PI.
2
Press
a
or
b
to turn the Auto PI seek
on or off.
Saving the battery
consumption
It is possible to save the battery consumption
when this unit is turned off. After one minute
of turning off this unit, this unit will be
switched into power save mode.
!
You cannot insert and eject a disc while
this unit is in power save mode.
!
You can only use
SOURCE
while this unit is
in power save mode.
Important
When you disconnect a battery in order to replace
it, this mode is turned off. When installing this
unit in a vehicle that does not have an ACC (ac-
cessory) position on the ignition switch, the vehi-
cle battery may be drained depending on a
connection method. After checking the connec-
tion method, turn this mode on if needed.
1
Press AUDIO to select SAVE.
2
Press
a
or
b
to turn power save on or
off.
Initial Settings
En
15
English
Section
08