Pioneer DEH-P790BT Other Manual - Page 1
Pioneer DEH-P790BT - Premier Radio / CD Manual
UPC - 012562853208
View all Pioneer DEH-P790BT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
INSTALLATION MANUAL DEH-P790BT This product conforms to CEMA cord colors. Le code de couleur des câbles utilisé pour ce produit est conforme à CEMA. Printed in Thailand Imprimé en Thaïlande UC MANUEL D'INSTALLATION Installation Note: • Check all connections and systems before final installation. • Do not use unauthorized parts. The use of unauthorized parts may cause malfunctions. • Consult with your dealer if installation requires drilling of holes or other modifications of the vehicle. • Do not install this unit where: - it may interfere with operation of the vehicle. - it may cause injury to a passenger as a result of a sudden stop. • The semiconductor laser will be damaged if it overheats. Install this unit away from hot places such as near the heater outlet. • Optimum performance is obtained when the unit is installed at an angle of less than 60°. 60° DIN Front/Rear-mount This unit can be properly installed either from "Front" (conventional DIN Front-mount) or "Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit chassis). For details, refer to the following installation methods. DIN Front-mount Installation with the rubber bush Dashboard Mounting sleeve 182 53 Rubber bush Screw • When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents. Leave ample space Dashboard 10 cm (3-7/8 in.) 1. Insert the mounting sleeve into the dashboard. • When installing in a shallow space, use a supplied mounting sleeve. If there is enough space behind the unit, use factory supplied mounting sleeve. 2. Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place. 3. Install the unit as illustrated. 10 cm (3-7/8 in.) Removing the Unit 1. Extend top and bottom of the trim ring outwards to remove the trim ring. When reattaching the trim ring, push the trim ring onto the unit until it clicks. (If the trim ring is attached upside down, the trim ring will not fit properly.) • It becomes easy to remove the trim ring if the front panel is released. Trim ring 2. Insert the supplied extraction keys into both sides of the unit until they click into place. 3. Pull the unit out of the dashboard. 2. Determine the appropriate position where the holes on the bracket and the side of the unit match. 3. Tighten two screws on each side. • Use either truss screws (5 mm × 8 mm) or flush surface screws (5 mm × 9 mm), depending on the shape of screw holes in the bracket. Screw Dashboard or Console Factory radio mounting bracket Fastening the front panel If you do not plan to detach the front panel, the front panel can be fastened with supplied screw. DIN Rear-mount 1. Extend top and bottom of the trim ring outwards to remove the trim ring. When reattaching the trim ring, push the trim ring onto the unit until it clicks. (If the trim ring is attached upside down, the trim ring will not fit properly.) • It becomes easy to remove the trim ring if the front panel is released. Trim ring Screw ENGLISH Installing the microphone Installation notes Install the microphone in a position and orientation that will enable it to pick up the voice of the person operating the system. CAUTION It is extremely dangerous to allow the microphone lead to become wound around the steering column or gearstick. Be sure to install the unit in such a way that it will not obstruct driving. When installing the microphone on the sun visor 1. Install the microphone on the microphone clip. 2. Install the microphone clip on the sun visor. With the sun visor up, install the microphone clip. (Lowering the sun visor reduces the recognition rate for voice operations.) Microphone clip Clamps Use clamps to secure the lead where necessary inside the vehicle. Microphone Microphone clip When installing the microphone on the steering column 1. Install the microphone on the microphone clip. Microphone Microphone clip Fit the microphone lead into the groove.