Pioneer GM-X862 Owner's Manual - Page 2

Setting the Unit Gain Control If the sound level is too low, even when the volume of the car stereo used along with this power amplifier is turned up, turn gain control on the front of the power amplifier clockwise. If the sound distorts when the volume is turned up, turn the gain control counter-clockwise. • When using with an RCA equipped car stereo (standard output of 500 mV), set to the NORMAL position. When using with an RCA equipped Pioneer car stereo with max. output of 4 V or more, adjust level to match the car stereo output level. Power Indicator The power indicator lights when the power is switched on. LPF (Low-Pass Filter) Select Switch Set the LPF select switch as follows according to the type of speaker that is connected to the speaker output connector and the car stereo system: LPF Select Switch LPF (left) OFF (right) Audio frequency range to be output Very Low Frequency range Full range Speaker Type Subwoofer Full range Remarks Connect a subwoofer. Connecting the Unit CAUTION • Disconnect the negative (-) terminal of the battery to avoid the risk of short-circuit and damage to the unit. • Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around it where they lie against metal parts. • Do not route wires where they will get hot, for example where the heater will blow over them. If the insulation heats up, it may become damaged, resulting in a short-circuit through the vehicle body. • Make sure that wires will not interfere with moving parts of the vehicle, such as the gearshift, handbrake or seat sliding mechanism. • Do not shorten any wires. Otherwise the protection circuit may fail to work when it should. • Never feed power to other equipment by cutting the insulation of the power supply wire to tap from the wire. The current capacity of the wire will be exceeded, causing overheating. To prevent damage • Do not ground the speaker wire directly or connect a negative (-) lead wire for several speakers. • This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck or bus, check the battery voltage. • If the car stereo is kept on for a long time while the engine is at rest or idling, the battery may go dead. Turn the car stereo off when the engine is at rest or idling. • If the system remote control wire of the amplifier is connected to the power terminal through the ignition switch (12 V DC), the amplifier will always be on when the ignition is on- regardless of whether the car stereo is on or off. Because of this, the battery could go dead if the engine is at rest or idling. • Speakers to be connected to the amplifier should conform with the standards listed below. If they do not conform, they may catch fire, emit smoke or become damaged. The speaker impedance must be 2 to 8 ohms for stereo connection, and 4 to 8 ohms for monaural and other bridge connection. • Install and route the separately sold battery wire as far away as possible from the speaker wires. Install and route the separately sold battery wire, ground wire, speaker wires and the amplifier as far away as possible from the antenna, antenna cable and tuner. • Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied Installation manuals of both products and connect cords that have the same function. GM-X962 Speaker Channel Two-channel One-channel GM-X862 Speaker Channel Two-channel One-channel Speaker Type Subwoofer Other than subwoofer Subwoofer Other than subwoofer Speaker Type Subwoofer Other than subwoofer Subwoofer Other than subwoofer Power Nominal input: Min. 145 W Max. input: Min. 250 W Nominal input: Min. 440 W Max. input: Min. 760 W Power Nominal input: Min. 145 W Max. input: Min. 250 W Nominal input: Min. 440 W Max. input: Min. 760 W Connection Diagram Fuse (30 A) Grommet Fuse (30 A) Special red battery wire [RD-223] (sold separately) After making all other connections at the amplifier, connect the battery wire terminal of the amplifier to the positive (+) terminal of the battery. Ground wire (black) [RD-223] (sold separately) Connect to metal body or chassis. Front side Connecting wires with RCA pin plugs (sold separately). Car stereo with RCA output jacks External Output RCA input jack GM-X962: Fuse (25 A) × 2 GM-X862: Fuse (25 A) × 2 Speaker terminal See the "Connecting the Speaker wires" section for speaker connection instructions. Back side System remote control wire (sold separately) Connect the male terminal of this wire to the system remote control terminal of the car stereo (SYSTEM REMOTE CONTROL). The female terminal can be connected to the auto-antenna relay control terminal. If the car stereo does not have a system remote control terminal, connect the male terminal to the power terminal through the ignition switch.