Pioneer PRO-950HD Operating Instructions - Page 21

Attaching/detaching the Pioneer stand - weight

Get Pioneer PRO-950HD PDF manuals and user guides View all Pioneer PRO-950HD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Preparation 05 Attaching/detaching the Pioneer stand The plasma display comes with the Pioneer table top stand attached. You can also install the display on a rack by detaching the stand. The method for attaching/detaching the stand varies depending on the product. Caution • This product can be used only with the attached stand. Using other stands can result in instability, possibly causing injury. • The weight of a 50 inch plasma display is about 34.8 kg (76.7 lbs.) and a 42 inch about 29.9 kg (65.9 lbs.), it has no depth, and is unstable. Therefore, at least two people must assemble and install it. Detaching the stand • Steps for detaching the stand are the same for PRO1150HD and PRO-950HD. Illustrations shown are for PRO1150HD. 1 With the plasma display lying flat, loosen and remove the two installation bolts (1) and (2) using a screwdriver. Installation bolts (1): M8 x 23 mm (black) for PRO-950HD M8 x 23 mm (black) for PRO-1150HD Installation bolts (2): M8 x 60 mm (black) for PRO-950HD M8 x 40 mm (black) for PRO-1150HD Note • Make sure to keep the installation bolts (1) and (2) that have been removed as they are re-used when attaching the stand to the plasma display. • Place a sheet or protective cover to protect the display from scratches or damage. • Work only with the plasma display lying flat on a table or similar surface. • When lying the plasma display down, be careful not to scratch or damage it. • If the speaker has been installed, it is recommended to detach the speaker before removing the stand (for PRO-1150HD only). Attaching the stand again • Steps for attaching the stand are the same for PRO1150HD and PRO-950HD (use the screw holes with "T" inscribed). Illustrations shown are for PRO-1150HD. 1 With the plasma display lying flat, fit the stand's support columns to the bottom of the plasma display as indicated by the arrows, then slowly insert them. • Be extremely careful not to insert the support columns of the stand into any part of the plasma display other than the stand insertion slots. Doing so might damage the plasma display panel or its ports or result in warping of the stand. Line up the column supports with the bottom of the plasma display, as indicated in the accompanying diagram. Installation bolts (1) (Step 1) Installation bolts (2) (Step 2) Plasma display Table top stand Sheet 2 Remove the stand from the plasma display. Insert the stand into the plasma display so that an arrow with "FRONT/FACE AVANT" mark inscribed at the bottom of the stand indicates downward. Sheet 21 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
21
En
Preparation
05
Attaching/detaching the Pioneer stand
The plasma display comes with the Pioneer table top stand
attached. You can also install the display on a rack by detaching
the stand. The method for attaching/detaching the stand varies
depending on the product.
Caution
• This product can be used only with the attached stand. Using
other stands can result in instability, possibly causing injury.
•
The weight of a 50 inch plasma display is about 34.8 kg (76.7
lbs.) and a 42 inch about 29.9 kg (65.9 lbs.), it has no depth, and
is unstable. Therefore, at least two people must assemble and
install it.
Detaching the stand
1
With the plasma display lying flat, loosen and remove
the two installation bolts (1) and (2) using a
screwdriver.
Installation bolts (1): M8 x 23 mm (black) for PRO-950HD
M8 x 23 mm (black) for PRO-1150HD
Installation bolts (2): M8 x 60 mm (black) for PRO-950HD
M8 x 40 mm (black) for PRO-1150HD
2
Remove the stand from the plasma display.
Note
• Make sure to keep the installation bolts (1) and (2) that have
been removed as they are re-used when attaching the stand to
the plasma display.
• Place a sheet or protective cover to protect the display from
scratches or damage.
•
Work only with the plasma display lying flat on a table or similar
surface.
•
When lying the plasma display down, be careful not to scratch
or damage it.
•
If the speaker has been installed, it is recommended to detach
the speaker before removing the stand (for PRO-1150HD only).
Attaching the stand again
1
With the plasma display lying flat, fit the stand’s
support columns to the bottom of the plasma display as
indicated by the arrows, then slowly insert them.
• Be extremely careful not to insert the support columns of
the stand into any part of the plasma display other than the
stand insertion slots. Doing so might damage the plasma
display panel or its ports or result in warping of the stand.
• Steps for detaching the stand are the same for PRO-
1150HD and PRO-950HD. Illustrations shown are for PRO-
1150HD.
Installation bolts (1)
(Step 1)
Installation bolts (2)
(Step 2)
Table top stand
Sheet
• Steps for attaching the stand are the same for PRO-
1150HD and PRO-950HD (use the screw holes with “T”
inscribed). Illustrations shown are for PRO-1150HD.
Sheet
Plasma
display
Line up the column supports
with the bottom of the
plasma display, as indicated
in the accompanying
diagram.
Insert the stand into the
plasma display so that an
arrow with “FRONT/FACE
AVANT” mark inscribed at
the bottom of the stand
indicates downward.