Pioneer SW501 Owner's Manual - Page 1

Operating Instructions Mode d'emploi S-W301/S-W501/S-W601 POWERED SUBWOOFER ENCEINTE ACTIVE D'EXTREMES GRAVES English Thank you for buying this PIONEER product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings. However, the method of connecting and operating the unit is the same. IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. D3-4-2-1-1_En-A If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal. The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation). D3-4-2-2-1a_A_En 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. VENTILATION CAUTION When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 25 cm at top, 15 cm at rear, and 10 cm at each side). WARNING Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed. D3-4-2-1-7b_A_En 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. P1-4-2-2_En POWER-CORD CAUTION Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement. S002*_En CAUTION The POWER switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation). D3-4-2-2-2a_A_En This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period. K041_En WARNING: Handling the cord on this product or cords associated with accessories sold with the product will expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defect or other reproductive harm. D36-P4_A_En Operating Environment Operating environment temperature and humidity: +5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light) D3-4-2-1-7c_A_En For U.S. Model WARNING To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment. D3-4-2-1-7a_A_En This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance : www.eiae.org. K057_En WARNING This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture. D3-4-2-1-3_B_En WARNING Before plugging in for the first time, read the following section carefully. The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V or 120 V) written on the rear panel. D3-4-2-1-4_A_En ACCESSORY ITEMS • RCA plug cord x1 • Operating instructions FEATURES n 150 W (S-W301)/170 W (S-W501)/180 W (S-W601) (RMS) power with AB class amplifier that serves audio and video software playback such as Dolby Digital with a wide dynamic range. n Equipped with 20 cm (S-W301)/25 cm (S-W501)/30 cm (S-W601) driver n Crossover frequency can be set to 50 Hz to 200 Hz. IN COMBINATION WITH SPEAKERS The frequency characteristics of the S-W301/S-W501/S-W601 combined with small-size speakers are shown below. As shown in these figures, the low frequency range is improved. • These special characteristics are obtained in an echoless chamber. The effect of an additional S-W301/S-W501/S-W601 in an ordinary listening room is better than the chart indicates when positioned adequately. Small-size speakers + S-W301/S-W501/S-W601 RESPONCE (dB) Small-size speakers FREQUENCY (Hz) • With playback of Dolby Digital, establishment of a special channel for the subwoofer is recommended; and with playback of LFE (Low Frequency Effect: sound effect like the rumbling of the earth, whose purpose is to intensify the force of the video), the S-W301/S-W501/SW601 is especially effective. INSTALLATION Speaker Installation • Subwoofer Installation Criteria 1 2 3 1 Left speaker 2 Right speaker 3 Recommended installation range for the subwoofer 4 Listening position 4 The subwoofer plays back the bass in monaural, making use of the fact that the human ear is not very sensitive to the direction of low-pitched sound. Because of this, the subwoofer can be installed almost anywhere. If it is installed too far away, however, the sound from the other speakers may become unnatural. • An example of speaker positioning 1 23 1 Front left speaker 2 Center speaker 3 Front right speaker 4 Subwoofer 5 Listening area 4 6 Rear left speaker 7 Rear right speaker 5 • The rear (surround) speakers are most effective when installed in parallel locations directly to the side, or slightly behind, the listener, at a level about 1 meter (3.3 ft.) above the listener's ears. CAUTION: When installing the center speaker on top of the TV, be sure to secure it with tape or some other suitable means. Otherwise, the speaker may fall from the TV due to external shocks such as earthquakes, and it may lead to endangering those nearby or damaging the speaker. Installation Precautions • Do not attach the subwoofer to the wall or ceiling. They may fall off and cause injury. • Install the unit in a well-ventilated location where it will not be exposed to high temperatures and high humidity. • Do not place the unit near stoves or other heating equipment or at locations exposed to direct sunlight, as these can have an adverse effect on the cabinet and internal components. Also, do not install the unit where there is too much dust or high humidity, as these can cause malfunctioning or breakdowns. (Avoid cooking tables and other locations where the unit would be exposed to heat, steam and soot.) • Do not place heavy or large objects on top of the speaker. Doing so could provoke the speaker to fall, causing damages or bodily injury. If speakers fall from their installation locations, they may suffer irreparable cracks in their finish. • Keep the unit away from devices such as cassette decks which are sensitive to magnetic fields. The subwoofer is not magnetically shielded and so should not be placed near a TV or monitor. Magnetic storage media (such as floppy discs and tape or video cassettes) should also not be kept close to the subwoofer. • Do not place the speaker on an unstable surface, as doing so may cause the speaker to fall and cause damage or bodily injury. • Do not place cups, glasses, or other containers with fluids on top of the units, since the units may be damaged if the liquid spills. • The installation location selected should have a sturdy floor surface. Mounting the speaker on a long-pile carpet should be avoided, since the carpet may touch the driver's diaphram, causing distorted sound. • Please install this unit away from the antenna cable of the tuner, as noise can be caused with installation close to the antenna cable. In such a case, use this unit at a position away from the antenna and the antenna cable, or when playback of extra bass is not required, switch off the power for this unit. MAINTENANCE OF EXTERNAL SURFACES: • Clean the surface by wiping with a soft, dry cloth. • When the surfaces are very dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water, and wrung out well, and then wipe again with a dry cloth. Do not use furniture wax or cleaners. • Never use thinners, benzine, insecticide sprays and other chemicals on or near this unit, since these will corrode the surfaces. 6 7 NOTES: • Position the left and right channel speakers at equal distances from the TV set and approximately 1.8 meters (6 ft.) from each other. • Install the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen. PANEL FACILITIES FRONT PANEL REAR PANEL STANDBY/ON 1 POWER VOLUME CROSSOVER MAX MIN 200 Hz 50 Hz BYPASS ON OFF PHASE AUTO STANDBY ON OFF LINE LEVEL OUTPUT INPUT 2 3 4 5 6 7 8 9 10 signal, and when set to 0º, it is in the same phase as the input signal. • Normally, the switch is set to 0º. But when the sound connection between the subwoofer and the left and right speakers sounds unnatural, try switching to 180º and set the switch in the position where the sound is natural. • When using two or more subwoofers together, make sure that the phase switch of all of them are set to the same position. 7 Auto Standby switch (AUTO STANDBY) Switches the Auto Standby feature on/off. When switched ON (the default setting is OFF), the Auto Standby feature becomes active. In this mode, if there is no input signal for 12 minutes the system automatically switches to standby. The power is automatically switched on again if an input signal is detected. NOTE: There may be cases where a connected component outputs noise or some other non-audio signal which causes this system to automatically power on when in Auto Standby mode. If this happens, switch off the Auto Standby mode and switch the system on/off manually. 8 Line Level Input terminal (LINE LEVEL INPUT) Connect to the SUBWOOFER PREOUT terminal of an amplifier or receiver, with the specially provided RCA plug cord. 9 Line Level Output terminal (LINE LEVEL OUTPUT) Used for connecting other equipment through the amplifier. The signal output from this jack is not affected in any way by the settings of the various controls on the unit. 10 AC CORD Connect the AC cord to a AC socket (in the room). CONNECTIONS Before making or changing any connections, switch off the power and disconnect both this unit and the amplifier/receiver from the AC outlet. LINE LEVEL CONNECTION Rear Panel Supplied RCA plug cord 1 Power Indicator (STANDBY/ON) Lights blue when the power has been switched ON. When AUTO STANDBY switch is set to ON, lights blue whenever the speaker receive an audio signal. If the power is switched OFF only briefly, the indicator lights blue when power is restored. If no signal is present for more than 12 minutes, the subwoofer automatically reverts to standby mode and the power indicator lights red. If, subsequently, a signal is received, power automatically comes back on and the power indicator lights blue. NOTE: • If you are planning on switching the unit OFF for a long period of time, make sure to check that the indicator light has gone out after switching OFF. 2 Power switch (POWER) Switches the subwoofer between ON and OFF. 3 Volume knob (VOLUME) Sets the subwoofer volume. • Turn the knob slowly from the MIN position. • With this unit, the bass level can be independently set, so do not turn up the bass on the AV amplifier. 4 Crossover knob (CROSSOVER) When using the subwoofer, set the upper frequency limit for the subwoofer (50 Hz to 200 Hz) so that it complements the output from your other speakers. When using the bass management features of an AV receiver, set to BYPASS ON in order to use the low-pass filter of the AV receiver for high quality sound. 5 Bypass switch (BYPASS) When set to ON, the audio signal is routed to the woofer unit, bypassing the amplifier's crossover circuit. 6 Phase switch (PHASE 0º /180º) When set to 180º, the output phase becomes the reverse of the input This connection is for an amplifier or receiver equipped with a SUBWOOFER PREOUT terminal. Connect to the LINE LEVEL INPUT terminal on this unit, using the specially provided RCA plug cord. NOTE: • When connected to the PREOUT terminal for surround center channel on the amplifier or receiver, the bass is heard only on the center channel, so it will be insufficient. OPERATION For details regarding operating part functions, refer to PANEL FACILITIES above. 1. Turn the POWER switch (2) ON. • If the unit's power cord is connected to a switched AC outlet on the amplifier or receiver and the switch is left ON, the unit can be turned ON/OFF together with the amplifier or receiver. • If the unit cannot be connected to the amplifier or receiver, turn the power to the amplifier or receiver ON before turning the power to the unit ON. When turning the power OFF, turn the power to the unit OFF before turning the power to the amplifier or receiver OFF. 2. Operate the amplifier or receiver and adjust the volume of the other speakers. 3. Adjust the volume of the bass with the VOLUME knob (3). • When necessary, operate the CROSSOVER knob (4) and PHASE switch (6), and then adjust with the VOLUME knob (3). 4. Turn the POWER switch (2) OFF. • The power indicator disappears. TROUBLESHOOTING Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work. SYMPTOM CAUSE REMEDY 1 No power is being supplied • Power supply plug is not correctly (Indicator does not light up when inserted. power switch is turned on.) • Insert plug securely. 2 No sound (Indicator is lit.) • Connection of accessory RCA plug cord is wrong or disconnected. • VOLUME knob is set to MIN. • Check again and connect correctly. • Turn clockwise slowly. 3 Sound is distorted. • Level is too high. • Turn the VOLUME knob counter-clockwise to lower the level. • Input level is too high. • Turn the amplifier's output level (volume, bass control, bass boost) counter-clockwise to lower the level. 4 Howling noise occurs. • No power supplied to the amplifier. • Connect an amplifier and supply power. • Subwoofer level is set too high. • Place the subwoofer a good distance from speakers. Turn the VOLUME knob counter-clockwise to lower the volume. 5 Much noise when listening to AM or FM broadcasts. • The AM loop antenna or the FM indoor • Increase the distance between the AM or FM antenna (for antenna is close to this unit. indoor use) and this unit. SPECIFICATIONS Cabinet Bass-reflex, floor-standing type Speaker S-W301 20 cm cone type S-W501 25 cm cone type S-W601 30 cm cone type Power Amplifier Continuous Power Output (RMS) S-W301 150 W/6 Ω (100 Hz) S-W501 170 W/6 Ω (100 Hz) S-W601 180 W/6 Ω (100 Hz) Input (sensitivity at 100 Hz) LINE LEVEL (RCA jack 200 mV Output (Level at 100 Hz) LINE LEVEL (RCA jack 200 mV Selectable CROSSOVER Frequencies 50 Hz to 200 Hz Outline Dimension S-W301 360 mm (W) x 360 mm (H) x 398.5 mm (D) 14.2 in. (W) x 14.2 in. (H) x 15.7 in. (D) S-W501 360 mm (W) x 380 mm (H) x 418.5 mm (D) 14.2 in. (W) x 15.0 in. (H) x 16.5 in. (D) S-W601 360 mm (W) x 430 mm (H) x 438.5 mm (D) 14.2 in. (W) x 16.9 in. (H) x 17.3 in. (D) Weight (without package) S-W301 14.6 kg/32 lb. 4 oz. S-W501 15.6 kg/34 lb. 7 oz. S-W601 17.2 kg/37 lb. 15 oz. Power Requirements 120 V, 60 Hz Power Consumption 144 W Power Consumption in standby 0.5 W Accessories RCA plug cord x1 Operating instructions Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical enjoyment. Now it's time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Association's Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion-and, most importantly, without affecting your sensitive hearing. Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of sound. So what sounds "normal" can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts. To establish a safe level: • Start your volume control at a low setting. • Slowly increase the sound until you can hear it comfortably and clearly, and without distortion. Once you have established a comfortable sound level: • Set the dial and leave it there. Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all, we want you listening for a lifetime. We Want You Listening For A Lifetime Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since hearing damage from loud noise is often undetectable until it is too late, this manufacturer and the Electronic Industries Association's Consumer Electronics Group recommend you avoid prolonged exposure to excessive noise. This list of sound levels is included for your protection. Decibel Level Example 30 Quiet library, soft whispers 40 Living room, refrigerator, bedroom away from traffic 50 Light traffic, normal conversation, quiet office 60 Air conditioner at 20 feet, sewing machine 70 Vacuum cleaner, hair dryer, noisy restaurant 80 Average city traffic, garbage disposals, alarm clock at two feet. THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE 90 Subway, motorcycle, truck traffic, lawn mower 100 Garbage truck, chain saw, pneumatic drill 120 Rock band concert in front of speakers, thunderclap 140 Gunshot blast, jet plane 180 Rocket launching pad Information courtesy of the Deafness Research Foundation. S001_En Specifications and design subject to possible modification without notice, due to improvements. is a trademark placed on a product with Pioneer's Phase Control technology. This technology enables high-grade sound reproduction through each component by improving overall phase matching. Published by Pioneer Corporation. Copyright © 2008 Pioneer Corporation. All rights reserved. PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404 PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: 1-877-283-5901, 905-479-4411 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11 PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300 PIONEER ELECTRONICS DE MEXICO S.A. DE C.V. Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270 K002_B_En