Pioneer SX-A6-J Operating Instructions - Page 15

Using the tuner

Get Pioneer SX-A6-J PDF manuals and user guides View all Pioneer SX-A6-J manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Using the tuner 05 Chapter 5: Using the tuner Listening to the radio The following steps show you how to tune in to FM and AM radio broadcasts. 1 Press TUNER then press BAND to select the tuner band. 2 Tune to a station. There are four ways to do this: Automatic tuning - Press and hold TUNE +/- for about a second. Searching automatically stops at the next station. Manual tuning - To change the frequency one step at a time, press TUNE +/-. High speed tuning - Press and hold TUNE +/- continuously. Direct access - Use the number buttons to enter the frequency (For example, to tune to 106.00 (FM), press 1, 0, 6, 0, 0).1 If the TUNED or STEREO indicators don't light when tuning to an FM station because the signal is weak, press the MPX button to switch the receiver into mono reception mode. This should improve the sound quality and allow you to enjoy the broadcast. Saving station presets This receiver can memorize up to 30 stations, stored in three banks of 10 stations each.2 1 Tune to a station you want to memorize then press T.EDIT. The display shows ST. MEMORY, then a blinking memory class. 2 Press CLASS to select one of the three classes then press ST +/- to select the station preset you want. 3 Press ENTER to store the station. Naming station presets You can your station presets for easy recall. 1 Choose the preset you want to name. See Listening to station presets below. 2 Press T.EDIT. A cursor appears at the first character position. 3 Input the name you want then press ENTER. Names can be up to four characters long. • Use the ST +/- buttons to select characters, and ENTER to confirm. If no character is input, a space is input. Tip • Once you have named a station preset, you can press DISPLAY when listening to a station to switch the display between the name and the frequency. Listening to station presets You will need to have some presets stored to do this. See Saving station presets above if you haven't done this already.3 1 Press TUNER to select the tuner. Note 1 If you make a mistake halfway through, press D.ACCESS twice to cancel the frequency and start over. 2 When saving an FM frequency, the MPX setting is also stored. 3 Station memories will be lost if the receiver is left disconnected from the AC power outlet for an extended period. 15 En Downloaded from www.Manualslib.com manuals search engine

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
Using the tuner
05
15
En
Chapter 5:
Using the tuner
Listening to the radio
The following steps show you how to tune in to
FM and AM radio broadcasts.
1
Press
TUNER
then press
BAND
to select
the tuner band.
2
Tune to a station.
There are four ways to do this:
Automatic tuning
– Press and hold
TUNE
+/–
for about a second. Searching
automatically stops at the next station.
Manual tuning
– To change the frequency
one step at a time, press
TUNE +/–
.
High speed tuning
– Press and hold
TUNE +/–
continuously.
Direct access
– Use the number buttons to
enter the frequency (For example, to tune
to
106.00
(FM), press
1
,
0
,
6
,
0
,
0
).
1
If the
TUNED
or
STEREO
indicators don't light
when tuning to an FM station because the
signal is weak, press the
MPX
button to switch
the receiver into mono reception mode. This
should improve the sound quality and allow
you to enjoy the broadcast.
Saving station presets
This receiver can memorize up to 30 stations,
stored in three banks of 10 stations each.
2
1
Tune to a station you want to memorize
then press
T.EDIT
.
The display shows
ST. MEMORY
, then a
blinking memory class.
2
Press CLASS to select one of the three
classes then press
ST +/–
to select the station
preset you want.
3
Press ENTER to store the station.
Naming station presets
You can your station presets for easy recall.
1
Choose the preset you want to name.
See
Listening to station presets
below.
2
Press
T.EDIT
.
A cursor appears at the first character position.
3
Input the name you want then press
ENTER
.
Names can be up to four characters long.
•
Use the
ST +/–
buttons to select
characters, and
ENTER
to confirm. If no
character is input, a space is input.
Tip
•
Once you have named a station preset, you
can press
DISPLAY
when listening to a
station to switch the display between the
name and the frequency.
Listening to station presets
You will need to have some presets stored to do
this. See
Saving station presets
above if you
haven’t done this already.
3
1
Press
TUNER
to select the tuner.
Note
1
If you make a mistake halfway through, press
D.ACCESS
twice to cancel the frequency and start over.
2
When saving an FM frequency, the
MPX
setting is also stored.
3
Station memories will be lost if the receiver is left disconnected from the AC power outlet for an extended period.
Downloaded from
www.Manualslib.com
manuals search engine