Pioneer VSX-516-K Owner's Manual - Page 36

Additional information, Resetting the main unit - remote control replacement

Page 36 highlights

10 Additional information Problem Remedy No sound from surround back • Refer to Speaker setting on page 28 to check the surround back speakers. speaker settings. • Refer to Channel level on page 28 to check the speaker levels. • Refer to Using surround back channel processing on page 24 to make sure surround back channel processing and the sound mode are set for surround back sound. No sound from subwoofer. • Make sure the subwoofer is switched on. • If the subwoofer has a volume knob, make sure it's turned up. • The Dolby Digital or DTS source you are listening to may not have an LFE channel. • Switch the subwoofer setting in Speaker setting on page 28 to YES or PLUS. • Switch the LFE Attenuator Setup on page 30 to LFEATT 0 or LFEATT 10. Noise during playback of a cassette deck. • Move the cassette deck further from your receiver, until the noise disappears. No sound is output or a noise • Set the digital volume level of the player to full, or to the neutral is output when software with position. DTS is played back. During a playback search, noise is output from a DTS compatible CD player. • This is not a malfunction, but be sure to turn the volume down to prevent the output of loud noise from your speakers. Can't operate the remote control. • Replace the batteries (refer to page 5). • Operate within 23 ft. (7 m), 30° of the remote sensor on the front panel (refer to page 5). • Remove the obstacle or operate from another position. • Avoid exposing the remote sensor on the front panel to direct light. The display is dark or off. • Press DIMMER on the remote repeatedly to return to the default. Resetting the main unit Use this procedure to reset all the receiver's settings to the factory default. Use the front panel controls to do this. 1 Switch the receiver into standby. 2 While holding down the TONE button, press and hold the STANDBY/ON button for about three seconds. 3 When you see RESET? appear in the display, press the ENTER button. OK? shows in the display. 4 Press SETUP to confirm. OK appears in the display to indicate that the receiver has been reset to the factory default settings. 36 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80

Additional information
10
36
En
Resetting the main unit
Use this procedure to reset all the receiver’s
settings to the factory default. Use the front
panel controls to do this.
1
Switch the receiver into standby.
2
While holding down the TONE button,
press and hold the
±
STANDBY/ON button for
about three seconds.
3
When you see RESET? appear in the
display, press the
ENTER
button.
OK?
shows in the display.
4
Press
SETUP
to confirm.
OK
appears in the display to indicate that the
receiver has been reset to the factory default
settings.
No sound from surround back
speakers.
• Refer to
Speaker setting
on page 28 to check the surround back
speaker settings.
• Refer to
Channel level
on page 28 to check the speaker levels.
• Refer to
Using surround back channel processing
on page 24 to
make sure surround back channel processing and the sound mode
are set for surround back sound.
No sound from subwoofer.
• Make sure the subwoofer is switched on.
• If the subwoofer has a volume knob, make sure it’s turned up.
• The Dolby Digital or DTS source you are listening to may not have
an LFE channel.
• Switch the subwoofer setting in
Speaker setting
on page 28 to
YES
or
PLUS
.
• Switch the
LFE Attenuator Setup
on page 30 to
LFEATT 0
or
LFEATT 10
.
Noise during playback of a
cassette deck.
• Move the cassette deck further from your receiver, until the noise
disappears.
No sound is output or a noise
is output when software with
DTS is played back.
• Set the digital volume level of the player to full, or to the neutral
position.
During a playback search,
noise is output from a DTS
compatible CD player.
• This is not a malfunction, but be sure to turn the volume down to
prevent the output of loud noise from your speakers.
Can’t operate the remote
control.
• Replace the batteries (refer to page 5).
• Operate within 23 ft. (7 m), 30° of the remote sensor on the front
panel (refer to page 5).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
The display is dark or off.
• Press
DIMMER
on the remote repeatedly to return to the default.
Problem
Remedy