Pioneer VSX-60 Owner's Manual - Page 85

12 The System Setup and Other Setup menus 3 Select the Volume Limit setting you want. Use this function to limit the maximum volume. The volume cannot be increased above the level set here, even by operating VOLUME button (or the dial on the front panel). ! OFF (default) - The maximum volume is not limited. ! -20.0dB/-10.0dB/0.0dB - The maximum volume is limited to the value set here. 4 Select the Mute Level setting you want. This sets how much the volume is to be turned down when MUTE is pressed. ! FULL (default) - No sound. ! -40.0dB/-20.0dB - The volume will be turned down to the level specified here. 5 When you're finished, press RETURN. You will return to the Other Setup menu. Remote Control Mode Setup ! Default setting: 1 This sets this receiver's remote control mode to prevent erroneous operation when multiple units of the receiver are being used. 1 Select 'Remote Control Mode Setup' from the Other Setup menu. 2 Select the Remote Control Mode setting you want. 3 Select 'OK' to change the remote control mode. 4 Follow the instructions on the screen to change the remote control's setting. See Operating multiple receivers on page 67. 5 When you're finished, press RETURN. You will return to the Other Setup menu. Software Update Use this procedure to update the receiver's software and check the version. There are two ways to update: via the Internet and via a USB memory device. Updating via the Internet is performed by accessing the file server from the receiver and downloading the file. This procedure is only possible if the receiver is connected to the Internet. Updating via a USB memory device is performed by downloading the update file from a computer, reading this file onto a USB memory device then inserting this USB memory device into the USB port on the receiver's front panel. With this procedure, the USB memory device containing the update file must first be inserted into the USB port on the receiver's front panel. ! If an update file is provided on the Pioneer website, download it onto your computer. When downloading an update file from the Pioneer website onto your computer, the file will be in ZIP format. Unzip the ZIP file before saving it on the USB memory device. If there are any old downloaded files or downloaded files for other models on the USB memory device, delete them. Important ! DO NOT unplug the power cord during updating. ! When updating via the Internet, do not disconnect the LAN cable. When updating via a USB memory device, do not disconnect the USB memory device. ! If updating is interrupted before it is completed, start updating over from the beginning. ! The receiver's settings may be reset when the software is updated. Information on the models for which the settings are reset is provided on the Pioneer website. Check the website before updating. 1 Select 'Software Update' from the Other Setup menu. 2 Select the update procedure. ! Update via Internet - The receiver checks whether updatable software is available via the Internet. ! Update via USB Memory - The receiver checks whether the USB memory device inserted into the USB port on the receiver's front panel contains updatable software. "Accessing" is displayed and the update file is checked. Wait a while. 3 Check on the screen whether or not an update file was found. If "New version found." is displayed, the update file has been found. The version number and updating time are displayed. If "This is the latest version. There is no need to update." is displayed, no update file has been found. 4 To update, select OK. The updating screen appears and updating is performed. ! The power turns off automatically once updating is completed. Software Update messages Status messages FILE ERROR UPDATE ERROR 1 to UPDATE ERROR 7 Update via USB UE11 UE22 UE33 Descriptions Try disconnecting then reconnecting the USB device or storing the update file again. If the error still occurs, try using a different USB memory device. No update file was found on the USB memory device. Store the file in the USB memory device's root directory. Turn the receiver's power off, then turn it back on and try updating the software again. If this message flashes, updating has failed. Update via a USB memory device. Put the update file on a USB memory device and connect the device to the USB port. When the file is found, software updating starts automatically. Updating has failed. Use the same procedure to update the software again. ZONE Setup When making multi-zone connections using the AUDIO ZONE 2 OUT terminals and performing playback in Zone 2, you can set whether to adjust the Zone 2 volume on the receiver or to fix it to a specific volume (-40 dB Fixed or 0 dB Fixed). This is set to Variable upon shipment from the factory, allowing the volume to be adjusted on the receiver. If you would like to adjust the volume from the connected amplifier, make the setting below. ! This setting is not possible if multi-zone settings have been made using the speaker terminals and Speaker System is set to anything other than ZONE 2. In this case, adjust the volume for the sub zones on the receiver. CAUTION ! Note that when Volume Level is set to 0 dB Fixed, the audio output from the AUDIO ZONE 2 OUT terminals is set to the maximum. Also, depending on the volume setting on the connected amplifier, large volumes may be produced even when Volume Level is set to -40 dB Fixed. 1 Select 'ZONE Setup' from the Other Setup menu. 2 Select 'ZONE 2', then press ENTER. 85