Pioneer VSX-D409 Owner's Manual - Page 26

Preparations Learning mode: Programming signals from other remote controls (VSX-D509S only) If preset codes are not available for your component(s), or the available preset codes do not operate correctly, you can use this function to program in signals from the remote control(s) of your other component(s). This operation can also be used after recalling a preset code to program additional operations not covered in the preset codes. SOURCE RECEIVER LED 1 Press SETUP and hold for 3 seconds. The visible LED will blink twice. 2 DVD RCV TV VCR MULTI CONTROL CD TUN CD-R TVC 1 2 3 MIDNIGHT 5.1CH ATT 4 5 6 SIGNAL SELECT 7 EFFECT 8 9 +10 DISC 0 ENTER TV CONTROL 2 2 Press the MULTI CONTROL button for the 2 component you want to control and then 2 press 9, 7, then 5 to select the LEARNING setup mode. The remote is ready to learn new commands from other remote controls. TV TV VOL TVFUNC MASTERVOLUME MENU CHANNEL FQ ST ST ENTER 8 D.ACCESS 3 FQ BAND 1 CLASS ¡ The LED flashes rapidly. ( ) To cancel LEARNING setup mode Press SETUP button. After ten seconds if no commands are entered the remote will revert to its previous mode. 3 Press the button to be programmed (for example the 3 [play] button). MPX 7 2 DTV ON / OFF 4 DTV MENU ¢ DSP TEST TONE CH SELECT CH LEVEL FL DIMMER 4 Point the remote controls at each other, about 1-2 inches apart, and press the button on the LOUDNESS FUNCTION MUTING SETUP Î 1,5 other remote control for the operation you want to program . AV PRE-PROGRAMMED AND LEARNING REMOTE CONTROL UNIT memo The highlighted keys can learn new functions. 1 Point the remote controls toward each other. 2 Press the button on the other remote control corresponding to the operation you wish to program. The LED on this receiver's remote will go out and then blink twice when the operation is learned. Press the teaching key repeatedly, varying the distances between the remotes, until you see this receiver's remote blink twice, indicating the operation has been learned. 1 - 2 inches CD-R TVC 3 ATT 6 9 DISC ENTER ST CLASS ¡ ¢ ÎÎ AV PRE-PROGRAMMED AND LEARNING REMOTE CONTROL UNIT LOUDNESS FUNCTION MUTING SETUP CH SELECT CH LEVEL FL DIMMER DSP TEST TONE DTV ON / OFF DTV MENU TVFUNC MASTERVOLUME EFFECT 4 BAND 1 FQ 8 FQ TNU ENTER MENU CHANNEL 0 8 5 5.1CH 2 MALTI CONTROL VCR T V TV CONTROL SOURCE RECEIVER CD TV 2 7 MPX D.ACCESS 3 ST TV VOL +10 SIGNAL SELECT 7 4 MIDNIGHT 1 DVD RCV SOURCE RECEIVER DVD RCV TV VCR MULTI CONTROL CD TUN CD-R TVC 1 2 3 MIDNIGHT 5.1CH ATT 4 5 6 SIGNAL SELECT 7 EFFECT 8 9 +10 DISC 0 ENTER TV CONTROL TV TV VOL TVFUNC MASTERVOLUME MENU CHANNEL FQ ST ST ENTER FQ 8 D.ACCESS 3 BAND 1 CLASS ¡ MPX DTV ON / OFF DTV MENU 7 4 ¢ 2 DSP TEST TONE CH SELECT CH LEVEL FL DIMMER LOUDNESS FUNCTION MUTING SETUP Î AV PRE-PROGRAMMED AND LEARNING REMOTE CONTROL UNIT To program additional operations for the current component Repeat steps 3 and 4. To program operations for another component Repeat steps 2 through 4. 5 Press SETUP to exit the LEARNING setup mode After ten seconds of inactivity the remote control will automatically leave the LEARNING mode and revert to its previous mode. memo Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together a farther apant. 26