Poulan HDF550E User Manual - Page 13

Customer, Responsibilities, Service, Adjustments

Page 13 highlights

CUSTOMER RESPONSIBILITIES MUFFLER Do not operate tiller without muffler. Do not tamper with exhaust system. Damaged mufflers or spark arresters could create a fire hazard. Inspect periodically and replace if necessary. If your engine is equipped with a spark arrester screen assembly, remove every 50 hours for cleaning and inspection. Replace if damaged. SPARK PLUG Replace spark plugs at the beginning of each tilling season or after every 50 hours of use, whichevercomes first. Spark plug type and gap setting are shown in "PRODUCT SPECIFICATIONS" on page 3 of this manual. TRANSMISSION Your transmission is sealed and will not require lubrication unless serviced. CLEANING • Clean engine, wheels, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automotive type wax. We do not recommend using a garden hose to clean your unit unless the muffler, air filter and carburetor are covered to keep water out. Water in engine can result in a shortened engine life. SERVICE AND ADJUSTMENTS CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TILLER TO ADJUST HANDLE HEIGHT (See Fig. 15) Factory assembly has provided lowest handle height: Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil. • If a higher handle height is desired, loosen the four nuts securing handle panel to engine brackets. • Slide handle panel to desired location. • Tighten the four nuts securely. ENGINE BRACKETS HANDLE PANEL NUTS (ALSO 2 ON LEFT SIDE OF TILLER) (1) I 0 O 0 II e TINE ARRANGEMENT Your outer tines can be assembled in several different ways to suit your tilling or cultivating needs. a CAUTION: Tines are sharp. Wear gloves or other protection when handling tines. NORMAL TILLING - 26" PATH (See Fig. 16) • Assemble holes "A" in tine hubs to holes "B" in tine shaft. CLEVIS PIN OUTER TINE A HAIRPIN CLIP FIG. 16 INNER TINE FIG. 15 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

CUSTOMER
RESPONSIBILITIES
MUFFLER
Do
not
operate
tiller
without
muffler.
Do
not
tamper
with
exhaust
system.
Damaged
mufflers
or
spark
arresters
could
create
a
fire
hazard.
Inspect
periodically
and
replace
if
necessary.
If
your
engine
is
equipped
with
a
spark
arrester
screen
assembly,
remove
every
50
hours
for
cleaning
and
inspection.
Replace
if
damaged.
SPARK
PLUG
Replace
spark
plugs
at
the
beginning
of
each
tilling
season
or
after
every
50
hours
of
use,
whichevercomes
first.
Spark
plug
type
and
gap
setting
are
shown
in
"PRODUCT
SPECI-
FICATIONS"
on
page
3
of
this
manual.
TRANSMISSION
Your
transmission
is
sealed
and
will
not
require
lubrication
unless
serviced.
CLEANING
Clean engine,
wheels,
finish,
etc.
of
all
foreign
matter.
Keep
finished
surfaces
and
wheels
free
of
all
gasoline,
oil,
etc.
Protect
painted
surfaces
with
automotive
type
wax.
We
do
not
recommend
using
a
garden
hose
to
clean
your
unit
unless
the
muffler,
air
filter
and
carburetor
are
covered
to
keep
water
out.
Water
in
engine
can
result
in
a
shortened
engine
life.
SERVICE
AND
ADJUSTMENTS
CAUTION:
Disconnect
spark
plug
wire
from
spark
plug
and
place
wire
where
it
cannot
come
into
contact
with
plug.
TILLER
TO
ADJUST
HANDLE
HEIGHT
(See
Fig.
15)
Factory
assembly
has
provided
lowest
handle
height:
Se-
lect
handle
height
best
suited
for
your
tilling
conditions.
Handle
height
will
be
different
when
tiller
digs
into
soil.
If
a
higher
handle
height
is
desired,
loosen
the
four
nuts
securing
handle
panel to
engine brackets.
Slide
handle
panel
to
desired
location.
Tighten
the
four
nuts
securely.
(1)
II
ENGINE
BRACKETS
e
O
I
0
0
HANDLE
PANEL
NUTS
(ALSO
2
ON
LEFT
SIDE
OF
TILLER)
FIG.
15
TINE
ARRANGEMENT
Your
outer
tines
can
be
assembled
in
several
different
ways
to
suit
your
tilling
or
cultivating
needs.
a
CAUTION:
Tines
are
sharp.
Wear
gloves
or
other
protection
when
han-
dling
tines.
NORMAL
TILLING
-
26"
PATH
(See
Fig.
16)
Assemble
holes
"A"
in
tine
hubs
to
holes
"B"
in
tine
shaft.
CLEVIS
PIN
A
HAIRPIN
CLIP
OUTER
TINE
INNER
TINE
FIG.
16
13