Poulan PB20H42LT User Manual - Page 7

CHECK BATTERY See Fig. 4, TO ROLL TRACTOR OFF SKID, See Op, eration for location

Get Poulan PB20H42LT PDF manuals and user guides View all Poulan PB20H42LT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

ASSEMBLY • Push down on seat to engage pads in slots and pull seat towards rear of tractor. • Raise seat and tighten bolt securely. • Remove tape and discard. • Lower seat into operating position and sit on seat. Press clutch/brake pedal all the way down. If operating position is not comfortable, adjust seat. To adjust seat: Grasp adjustment handle and pull up, slide seat to desired position and release adjustment handle. SLOT PAD FLAT WASHER TAPE SEAT PAN BOLT TAB Fig. 3 ADJUSTMENT HANDLE CHECK BATTERY (See Fig. 4) • Lift seat pan to raised position. • If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in MAINTENANCE section of this manual for charging instructions). SEAT PAN LABEL TERMINAL TERMINAL NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid. WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects. TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls) • Press lift lever plunger and raise attachment lift lever to its highest position. • Release parking brake by depressing clutch/brake pedal. • Place freewheel control in "transmission disengaged position" (See "TO TRANSPORT" in the Operation section of this manual). • Roll tractor forward off skid. • Remove banding holding the deflector shield up against tractor. TO DRIVE TRACTOR OFF SKID (See Operation section for location and function of controls) • Be sure all the above assembly steps have been completed. • Check engine oil level and fill fuel tank with gasoline. • Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual). • Sit on seat in operating position, depress clutch/brake pedal and set the parking brake. • Place motion control lever in neutral (N) position. • Press lift lever plunger and raise attachment lift lever to its highest position. • Remove key from bag and start the engine (see "TO START ENGINE" in the Operation section of this manual). After engine has started, move throttle control to idle (slow) position. • Release parking brake. • Slowly move the motion control lever forward and slowly drive tractor off skid. • Apply brake to stop tractor, set parking brake and place motion control lever in neutral position. • Turn ignition key to "STOP" position. Continue with the instructions that follow. FIG. 4 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
7
ASSEMBLY
FIG. 4
CHECK BATTERY (See Fig. 4)
•
Lift seat pan to raised position.
•
If this battery is put into service after month and year
indicated on label (label located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in MAINTENANCE section of this
manual for charging instructions).
SEAT PAN
LABEL
TERMINAL
TERMINAL
•
Push down on seat to engage pads in slots and pull
seat towards rear of tractor.
•
Raise seat and tighten bolt securely.
•
Remove tape and discard.
•
Lower seat into operating position and sit on seat.
Press clutch/brake pedal all the way down. If operating
position is not comfortable, adjust seat.
To adjust seat: Grasp adjustment handle and pull up, slide
seat to desired position and release adjustment handle.
Fig. 3
BOLT
FLAT
WASHER
SEAT PAN
PAD
TAPE
SLOT
TAB
ADJUSTMENT
HANDLE
NOTE:
You may now roll or drive your tractor off the skid.
Follow the appropriate instruction below to remove the
tractor from the skid.
WARNING:
Before starting, read, understand and follow
all instructions in the Operation section of this manual. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other people and objects.
TO ROLL TRACTOR OFF SKID
(See Op-
eration section for location and function of
controls)
•
Press lift lever plunger and raise attachment lift lever
to its highest position.
•
Release parking brake by depressing clutch/brake
pedal.
•
Place freewheel control in "transmission disengaged
position" (See “TO TRANSPORT” in the Operation
section of this manual).
•
Roll tractor forward off skid.
•
Remove banding holding the deflector shield up against
tractor.
TO DRIVE TRACTOR OFF SKID (See Op-
eration section for location and function of
controls)
•
Be sure all the above assembly steps have been com-
pleted.
•
Check engine oil level and fill fuel tank with gasoline.
•
Place freewheel control in "transmission engaged"
position (see "TO TRANSPORT" in Operation section
of this manual).
•
Sit on seat in operating position, depress clutch/brake
pedal and set the parking brake.
•
Place motion control lever in neutral (N) position.
•
Press lift lever plunger and raise attachment lift lever
to its highest position.
•
Remove key from bag and start the engine (see "TO
START ENGINE" in the Operation section of this
manual). After engine has started, move throttle control
to idle (slow) position.
•
Release parking brake.
•
Slowly move the motion control lever forward and slowly
drive tractor off skid.
•
Apply brake to stop tractor, set parking brake and place
motion control lever in neutral position.
•
Turn ignition key to "STOP" position.
Continue with the instructions that follow.