Poulan PO15542LT User Manual - Page 7

TO ROLL TRACTOR OFF SKID, See Op, eration for location and function of, controls, CHECK

Get Poulan PO15542LT PDF manuals and user guides View all Poulan PO15542LT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

ASSEMBLY INSTALL SEAT (See Fig. 2) Adjust seat before tightening adjustment bolt. • Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. • Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard. • Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan. • Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor. • Pivot seat and pan forward and assemble adjustment bolt, lockwasher and flat washer loosely. Do not tighten • Lower seat into operating position and sit on seat. • Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down. • Get off seat without moving its adjusted position. • Raise seat and tighten adjustment bolt securely. SEAT SHOULDER BOLT SEAT PAN 2466 FLAT WASHER LOCK WASHER CHECK BATTERY (See Fig. 3) • Lift seat pan to raised position. • If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in MAINTENANCE section of this manual for charging instructions). SEAT PAN LABEL TERMINAL TERMINAL FIG. 3 NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid. WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects. TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls) • Press lift lever plunger and raise attachment lift lever to its highest position. • Release parking brake by depressing clutch/brake pedal. • Place gearshift lever in neutral (N) position. • Roll tractor forward off skid. • Remove banding holding deflector shield up against tractor. 02465 ADJUSTMENT BOLT FIG. 2 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
7
ASSEMBLY
FIG. 2
TO ROLL TRACTOR OFF SKID
(See Op-
eration section for location and function of
controls)
•
Press lift lever plunger and raise attachment lift lever
to its highest position.
•
Release parking brake by depressing clutch/brake
pedal.
•
Place gearshift lever in neutral (N) position.
•
Roll tractor forward off skid.
•
Remove banding holding deflector shield up against
tractor.
FIG. 3
CHECK BATTERY (See Fig. 3)
•
Lift seat pan to raised position.
•
If this battery is put into service after month and year
indicated on label (label located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in MAINTENANCE section of this
manual for charging instructions).
SEAT PAN
LABEL
TERMINAL
TERMINAL
NOTE:
You may now roll or drive your tractor off the skid.
Follow the appropriate instruction below to remove the
tractor from the skid.
WARNING:
Before starting, read, understand and follow
all instructions in the Operation section of this manual. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other people and objects.
ADJUSTMENT
BOLT
LOCK WASHER
INSTALL SEAT (See Fig. 2)
Adjust seat before tightening adjustment bolt.
•
Remove adjustment bolt, lock washer and flat washer
securing seat to cardboard packing and set aside for
assembly of seat to tractor.
•
Pivot seat upward and remove from the cardboard pack-
ing. Remove the cardboard packing and discard.
•
Place seat on seat pan so head of shoulder bolt is
positioned over large slotted hole in pan.
•
Push down on seat to engage shoulder bolt in slot and
pull seat towards rear of tractor.
•
Pivot seat and pan forward and assemble adjust-
ment bolt, lockwasher and flat washer loosely. Do not
tighten
•
Lower seat into operating position and sit on seat.
•
Slide seat until a comfortable position is reached
which allows you to press clutch/brake pedal all the
way down.
•
Get off seat without moving its adjusted position.
•
Raise seat and tighten adjustment bolt securely.
2466
02465
SEAT PAN
SHOULDER
BOLT
FLAT WASHER
SEAT