Poulan PR17542STB User Manual - Page 21

To Replace Mower Blade Drive Belt, See Fig. 21, To Check And Adjust Brake See Fig.

Get Poulan PR17542STB PDF manuals and user guides View all Poulan PR17542STB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 21) The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake. BELT REMOVAL • Remove mower from tractor (See "TO REMOVE MOWER" in this section of this manual). • Work belt off both mandrel pulleys and idler pulleys. • Pull belt away from mower. BELT INSTALLATION • Install new belt in reverse order of removal. • Make sure belt is in all pulley grooves and inside all belt guides. • Install mower in reverse order of removal instructions. IDLER PULLEYS MANDREL PULLEY TO ADJUST BRAKE • Depress clutch/brake pedal all the way down and engage parking brake. • Measure distance between brake operating arm and nut "A" on brake rod. • If distance is other than 1-1/2", loosen jam nut and turn nut "A" until distance becomes 1-1/2". Retighten jam nut against nut "A". • Engage transmission by placing freewheel control in "transmission engaged" position. • Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center. WITH PARKING BRAKE "ENGAGED" NUT 1-1/2" "A" JAM NUT MANDREL PULLEY FIG. 21 TO CHECK AND ADJUST BRAKE (See Fig. 22) Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle. If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. TO CHECK BRAKE • Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and engage parking brake. • Disengage transmission by placing freewheel control in "transmission disengaged" position. Pull freewheel control out and into the slot and release so it is held in the disengaged position. The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced. OPERATING ARM DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUSTMENT IS NECESSARY CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/DEPARTMENT FIG. 22 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
21
SERVICE AND ADJUSTMENTS
TO REPLACE MOWER BLADE DRIVE BELT
(See Fig. 21)
The mower blade drive belt may be replaced without tools.
Park the tractor on level surface.
Engage parking brake.
BELT REMOVAL
•
Remove mower from tractor (See “TO REMOVE
MOWER” in this section of this manual).
•
Work belt off both mandrel pulleys and idler pulleys.
•
Pull belt away from mower.
BELT INSTALLATION
•
Install new belt in reverse order of removal.
•
Make sure belt is in all pulley grooves and inside all belt
guides.
•
Install mower in reverse order of removal instructions.
FIG. 21
TO CHECK AND ADJUST BRAKE (See Fig.
22)
Your tractor is equipped with an adjustable brake system
which is mounted on the right side of the transaxle.
If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be checked and adjusted.
TO CHECK BRAKE
•
Park tractor on a level, dry concrete or paved surface,
depress clutch/brake pedal all the way down and engage
parking brake.
•
Disengage transmission by placing freewheel control in
“transmission disengaged” position. Pull freewheel con-
trol out and into the slot and release so it is held in the
disengaged position.
The rear wheels must lock and skid when you try to manually
push the tractor forward. If the rear wheels rotate, the brake
needs to be adjusted or the pads need to be replaced.
WITH PARKING BRAKE “ENGAGED”
JAM NUT
DO NOT TOUCH THIS NUT.
IF FURTHER
BRAKE ADJUSTMENT IS NECESSARY
CONTACT YOUR NEAREST AUTHORIZED
SERVICE CENTER/DEPARTMENT
OPERATING
ARM
NUT
“A”
FIG. 22
1-1/2”
IDLER
PULLEYS
MANDREL
PULLEY
MANDREL
PULLEY
TO ADJUST BRAKE
•
Depress clutch/brake pedal all the way down and en-
gage parking brake.
•
Measure distance between brake operating arm and nut
“A” on brake rod.
•
If distance is other than 1-1/2", loosen jam nut and turn
nut “A” until distance becomes 1-1/2".
Retighten jam nut
against nut “A”.
•
Engage transmission by placing freewheel control in
“transmission engaged” position.
•
Road test tractor for proper stopping distance as stated
above.
Readjust if necessary.
If stopping distance is
still greater than five (5) feet in highest gear, further
maintenance is necessary.
Replace brake pads or
contact a qualified service center.