Poulan PR5020 Owner Manual - Page 17

Poulan PR5020 Manual

Get Poulan PR5020 PDF manuals and user guides View all Poulan PR5020 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

RESETTING THE CHAIN BRAKE If the clutch cover is removed accidentally while the chain brake is locked, the chain brake must be unlocked so the clutch cover can be assembled without binding to the clutch drum. Align the notches on the bar tool so that they fit over the brake rotating link. CAUTION: The chain brake spring is under tension. Use care when resetting the brake. To reset the brake, rotate the link clockwise until it stops. NOTE: do not hold the brake band while attempting to reset it. The front link will be in its downward rotated position when the chain brake is unlocked. STORAGE Perform the following steps after each use: • Allow the engine to cool, and secure the unit before storing or transporting. • Store chain saw and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. • Store chain saw with all guards in place and position chain saw so that any sharp object cannot accidentally cause injury. • Store chain saw well out of the reach of children. • At the beginning of the next season, use only fresh fuel having the proper petrol to oil ratio. OTHER • Do not store petrol from one season to another. • Replace your petrol container if it starts to rust. SEASONAL STORAGE Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more. If your chain saw is to be stored for a period of time: • Clean saw thoroughly before storage. • Store in a clean dry area. • Lightly oil external metal surfaces and guide bar. • Oil the chain and wrap it in heavy paper or cloth. FUEL SYSTEM Under FUELING ENGINE in the OPERATION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your chain saw. Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the petrol in the fuel tank or fuel storage container. Follow the mix instructions found on stabilizer containers. Run engine at least 5 minutes after adding stabilizer. ENGINE • Remove spark plug and pour 1 teaspoon of 2-cycle engine oil through the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil. • Replace spark plug with new one of recommended type and heat range. • Clean air filter. • Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
RESETTING THE CHAIN BRAKE
If the clutch cover is removed accidentally while
the chain brake is locked, the chain brake must be
unlocked so the clutch cover can be assembled
without binding to the clutch drum.
Align the notches on the bar tool so that they Ft over
the brake rotating link.
CAUTION: The chain brake spring is under tension.
Use care when resetting the brake.
To reset the brake, rotate the link clockwise until
it stops. NOTE: do not hold the brake band while
attempting to reset it.
The front link will be in its downward rotated position
when the chain brake is unlocked.
STORAGE
Perform the following steps after each use:
•
Allow the engine to cool, and secure the unit before
storing or transporting.
•
Store chain saw and fuel in a well ventilated area
where fuel vapors cannot reach sparks or open
±ames from water heaters, electric motors or
switches, furnaces, etc.
•
Store chain saw with all guards in place and
position chain saw so that any sharp object cannot
accidentally cause injury.
•
Store chain saw well out of the reach of children.
SEASONAL STORAGE
Prepare your unit for storage at the end of the season
or if it will not be used for 30 days or more.
If your chain saw is to be stored for a period of time:
•
Clean saw thoroughly before storage.
•
Store in a clean dry area.
• Lightly oil external metal surfaces and guide bar.
•
Oil the chain and wrap it in heavy paper or cloth.
FUEL SYSTEM
Under FUELING ENGINE in the OPERATION section
of this manual, see message labeled
IMPORTANT regarding the use of gasohol in your
chain saw.
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits during
storage. Add stabilizer to the petrol in the fuel tank or
fuel storage container.
²ollow the mix instructions found on stabilizer
containers. Run engine at least 5 minutes after adding
stabilizer.
ENGINE
• Remove spark plug and pour 1 teaspoon of 2-cycle
engine oil through the spark plug opening. Slowly
pull the starter rope 8 to 10 times to distribute oil.
•
Replace spark plug with new one of recommended
type and heat range.
• Clean air Flter.
•
Check entire unit for loose screws, nuts, and bolts.
Replace any damaged, broken, or worn parts.
• At the beginning of the next season, use only fresh
fuel having the proper petrol to oil ratio.
OTHER
•
Do not store petrol from one season to another.
•
Replace your petrol container if it starts to rust.
17