ProForm 14.0 Ce Elliptical English Manual - Page 26

Maintenance And Troubleshooting

Get ProForm 14.0 Ce Elliptical PDF manuals and user guides View all ProForm 14.0 Ce Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

MAINTENANCE AND TROUBLESHOOTING Inspect and tighten all parts of the elliptical regularly. Replace any worn parts immediately. To clean the elliptical, use a damp cloth and a small amount of mild soap. IMPORTANT: To avoid damage 20 to the console, keep liquids away from the console and keep the console out of direct sunlight. CONSOLE TROUBLESHOOTING If the console does not turn on, make sure that the power cord is fully plugged in. If lines appear in the console display, see HOW TO CHANGE CONSOLE SETTINGS on page 25 and adjust the contrast level of the display. If the handgrip heart rate monitor does not function properly, see step 5 on page 20. Next, look into the access opening and locate the Reed Switch (69). Rotate the Pulley (74) until a Pulley Magnet (75) is aligned with the Reed Switch. HOW TO CALIBRATE THE RAMP If the ramp is not functioning properly, the ramp may need to be calibrated. To calibrate the ramp, press and hold the Calories button for several seconds until the test mode appears in the display. Press the Calories button again. Then, press the Power Ramp increase or decrease button to calibrate the ramp. The ramp will move upward and downward as it calibrates. When the ramp stops moving, the ramp is calibrated. Then, press the Calories button repeatedly to exit the calibration mode. 75 106 74 69 HOW TO ADJUST THE REED SWITCH If the console does not display correct feedback, the reed switch should be adjusted. To adjust the reed switch, first unplug the power cord. Using a flat screwdriver, release the tabs on the Access Cover (20) and pry the Access Cover upward off the elliptical. Next, loosen, but do not remove, the indicated M4 x 16mm Screw (106). Slide the Reed Switch (69) slightly toward or away from the Pulley Magnet (75). Then, retighten the M4 x 16mm Screw. Plug in the power cord and rotate the pulley for a moment. Repeat these actions until the console displays correct feedback. When the reed switch is correctly adjusted, reattach the access cover. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
26
Inspect and tighten all parts of the elliptical regularly.
Replace any worn parts immediately.
To clean the elliptical, use a damp cloth and a small
amount of mild soap.
IMPORTANT: To avoid damage
to the console, keep liquids away from the console
and keep the console out of direct sunlight.
CONSOLE TROUBLESHOOTING
If the console does not turn on, make sure that the
power cord is fully plugged in. If lines appear in the
console display, see HOW TO CHANGE CONSOLE
SETTINGS on page 25 and adjust the contrast level
of the display.
If the handgrip heart rate monitor does not function
properly, see step 5 on page 20.
HOW TO CALIBRATE THE RAMP
If the ramp is not functioning properly, the ramp may
need to be calibrated. To calibrate the ramp, press and
hold the Calories button for several seconds until the
test mode appears in the display.
Press the Calories button again. Then, press the
Power Ramp increase or decrease button to calibrate
the ramp. The ramp will move upward and downward
as it calibrates.
When the ramp stops moving, the ramp is calibrated.
Then, press the Calories button repeatedly to exit the
calibration mode.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted.
To adjust the reed switch, first
unplug the power
cord.
Using a flat screwdriver, release the tabs on the
Access Cover (20) and pry the Access Cover upward
off the elliptical.
Next, look into the access opening and locate the
Reed Switch (69). Rotate the Pulley (74) until a Pulley
Magnet (75) is aligned with the Reed Switch.
Next, loosen, but do not remove, the indicated M4 x
16mm Screw (106). Slide the Reed Switch (69) slightly
toward or away from the Pulley Magnet (75). Then,
retighten the M4 x 16mm Screw.
Plug in the power cord and rotate the pulley for a
moment. Repeat these actions until the console
displays correct feedback. When the reed switch is cor-
rectly adjusted, reattach the access cover.
MAINTENANCE AND TROUBLESHOOTING
20
106
69
74
75