ProForm 205 Cst Treadmill Uk Manual - Page 23

Unplug The Power Cord.

Get ProForm 205 Cst Treadmill PDF manuals and user guides View all ProForm 205 Cst Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

SYMPTOM: The console displays do not function properly SYMPTOM: The console displays remain lit when you remove the key from the console a. Remove the key from the console and UNPLUG THE POWER CORD. Next, place the treadmill in the storage position (see HOW TO FOLD THE TREADMILL on page 21). Remove the five indicated M4.2 x 19mm Washer Head Screws (12). Then, carefully remove the Motor Hood (69). a. The console features a display demo mode, designed to be used if the treadmill is displayed in a store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE SETTINGS MODE on page 18 to turn off the demo mode. 69 12 12 SYMPTOM: The walking belt slows when walked on a. If an extension cord is needed, use only a 3-conductor, 14-gauge (2 mm2) cord that is no longer than 5 ft. (1.5 m). 12 Next, locate the Reed Switch (111) and the Magnet (110) on the left side of the Pulley (59). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the #8 x 3/4" Truss Head Screw (112), move the Reed Switch slightly, and then retighten the Screw. Reattach the Motor Hood (not shown), and walk on the treadmill for a few minutes to check for a correct speed reading. b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened. b 2-3 in. Top View 1/8 in. 18102 111 59 110 Idler Roller Screws 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
23
SYMPTOM: The console displays do not function
properly
a.
Remove the key from the console and
UNPLUG
THE POWER CORD.
Next, place the treadmill in
the storage position (see HOW TO FOLD THE
TREADMILL on page 21).
Remove the five indicated M4.2 x 19mm Washer
Head Screws (12). Then, carefully remove the
Motor Hood (69).
Next, locate the Reed Switch (111) and the Magnet
(110) on the left side of the Pulley (59). Turn the
Pulley until the Magnet is aligned with the Reed
Switch.
Make sure that the gap between the
Magnet and the Reed Switch is about 1/8 in.
(3 mm).
If necessary, loosen the #8 x 3/4" Truss
Head Screw (112), move the Reed Switch slightly,
and then retighten the Screw. Reattach the Motor
Hood (not shown), and walk on the treadmill for a
few minutes to check for a correct speed reading.
SYMPTOM: The console displays remain lit when
you remove the key from the console
a.
The console features a display demo mode,
designed to be used if the treadmill is displayed in
a store. If the displays remain lit when you remove
the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a
few seconds. If the displays are still lit, see THE
SETTINGS MODE on page 18 to turn off the demo
mode.
SYMPTOM: The walking belt slows when walked on
a.
If an extension cord is needed, use only a 3-con-
ductor, 14-gauge (2 mm
2
) cord that is no longer
than 5 ft. (1.5 m).
b.
If the walking belt is overtightened, treadmill
performance may decrease and the walking belt
may become damaged. Remove the key and
UNPLUG THE POWER CORD.
Using the hex key,
turn both idler roller screws counterclockwise, 1/4
of a turn. When the walking belt is properly tight-
ened, you should be able to lift each edge of the
walking belt 2 to 3 in. (5 to 7 cm) off the walking
platform. Be careful to keep the walking belt
centered. Then, plug in the power cord, insert the
key, and walk on the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
69
12
12
12
110
Top
View
59
112
111
1/8 in.
Idler Roller Screws
2–3 in.
b