ProForm 500 Lx Treadmill English Manual - Page 7

Harness 28 in the Right Upright.

Page 7 highlights

2. Orient the Right Upright (36) so that the square hole at the lower end is in the position shown. Attach the Right Upright to the Upright Base (48) with two Upright Bolts (40) and two Upright Star Washers (39). Do not tighten the Upright Bolts yet. Attach each Wheel (45) to the Upright Base (48) with a Wheel Bolt (40), two Wheel Spacers (44), and a Nut (47) as shown. Do not overtighten the Nuts; the Wheels should turn freely. 2 36 47 45 44 44 47 40 Square Hole 48 44 40 45 39 40 3. Cut the tie holding the Wire Harness (28) in a bundle. Leave 3 the large colored tie on the end of the Upright Wire. Orient the Upright Base (48) on the Wheels (45) as shown, and center the frame assembly between the Uprights (31, 36). With the help of another person, lower the frame assembly and insert the Wire Harness (28) into the large hole at the bottom of the Right Upright (36) and out of the top. While the frame assembly is raised, raise the Uprights (31, 36) so the Upright Base (48) is flat on the floor. Make sure that the end of the Wire Harness (28) does not fall into the Right Upright (36). It may be helpful to bend the colored tie on the end of the Wire Harness over the Right Upright. 4. Orient the two Frame Spacers (34) as shown in the inset 4 drawing. Open the included packet of grease and apply grease equally to both sides of each Frame Spacer. Hold a Frame Spacer (34) between the frame assembly and the Right Upright (36). Make sure that the Frame Spacer is oriented as shown in the inset drawing. Insert a Frame Bolt (32) through a Frame Washer (33), the Right Upright, the Frame Spacer, and the bracket on the frame assembly. Be careful not to pinch the Wire Harness (28) in the Right Upright. Finger tighten a Nut (47) onto the Frame Bolt. Do not fully tighten the Nut yet. Repeat this step on the left side. Note: There is not a wire harness on the left side. Hole 48 31 28 36 45 Frame Assembly Colored Tie 28 28 36 34 Left Side 34 Right Side Bracket 47 33 34 32 Frame Assembly 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22

7
2.
Orient the Right Upright (36) so that the square hole at
the lower end is in the position shown. Attach the Right
Upright to the Upright Base (48) with two Upright Bolts
(40) and two Upright Star Washers (39).
Do not tighten
the Upright Bolts yet.
Attach each Wheel (45) to the Upright Base (48) with a
Wheel Bolt (40), two Wheel Spacers (44), and a Nut (47)
as shown.
Do not overtighten the Nuts;
the Wheels
should turn freely.
48
Square Hole
45
47
44
40
45
44
36
44
40
47
2
3.
Cut the tie holding the Wire Harness (28) in a bundle.
Leave
the large colored tie on the end of the Upright Wire.
Orient the Upright Base (48) on the Wheels (45) as
shown, and center the frame assembly between the
Uprights (31, 36). With the help of another person, lower
the frame assembly and insert the Wire Harness (28) into
the large hole at the bottom of the Right Upright (36) and
out of the top.
While the frame assembly is raised, raise the Uprights
(31, 36) so the Upright Base (48) is flat on the floor.
Make
sure that the end of the Wire Harness (28) does not
fall into the Right Upright (36). It may be helpful to
bend the colored tie on the end of the Wire Harness
over the Right Upright.
28
Colored Tie
48
28
36
31
45
3
4.
Orient the two Frame Spacers (34) as shown in the inset
drawing. Open the included packet of grease and apply
grease equally to both sides of each Frame Spacer.
Hold a Frame Spacer (34) between the frame assembly
and the Right Upright (36).
Make sure that the Frame
Spacer is oriented as shown in the inset drawing.
Insert a Frame Bolt (32) through a Frame Washer (33),
the Right Upright, the Frame Spacer, and the bracket on
the frame assembly.
Be careful not to pinch the Wire
Harness (28) in the Right Upright.
Finger tighten a Nut
(47) onto the Frame Bolt.
Do not fully tighten the Nut
yet.
Repeat this step on the left side. Note: There is not a
wire harness on the left side.
Frame Assembly
Bracket
Frame Assembly
Hole
32
34
33
4
47
28
36
Right
Side
Left
Side
34
34
40
39