ProForm 610 Tr Treadmill English Manual - Page 6

Assembly

Get ProForm 610 Tr Treadmill PDF manuals and user guides View all ProForm 610 Tr Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

ASSEMBLY To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480. Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly requires the included hex key and your own Phillips screwdriver and adjustable wrench . Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of the manual. The number after the parentheses shows the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to one of the parts to be assembled. Extra hardware may be included. To avoid damaging plastic parts, do not use power tools for assembly. 3/4" Screw (10)-5 Base Pad Spacer (25)-2 3/8" Star 5/16" Star Washer (9)-4 Washer (7)-4 3/8" Nut (8)-2 1" Tek Screw (56)-4 3/8" x 2" Bolt (4)-2 5/16" x 1" Bolt (5)-4 3/8" x 4" Bolt (6)-4 1. Make sure that the power cord is unplugged. 1 With the help of a second person, carefully tip the treadmill onto its left side. Partially fold the Frame (53) so that the treadmill is more stable; do not fully fold the Frame yet. Remove and discard the two indicated bolts (A) and the shipping bracket (B). Cut the tie securing the Upright Wire (78) to the Base (80). Locate the tie in the indicated hole in the Base, and use the tie to pull the Upright Wire out of the hole. Attach a Base Pad (79) to the Base (80) in the location shown with a Base Pad Spacer (25) and a 1" Tek Screw (56). Then, attach another Base Pad (79) with only a 1" Tek Screw (56). 6 B Hole 80 53 25 79 56 A 78 79 56 Tie

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480. Assembly
requires two persons.
Set the treadmill in a cleared area and remove all packing materials;
do not dispose of
the packing materials until assembly is completed.
Note: The underside of the treadmill walking belt is coated
with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the
walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the
walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex key
and your own Phillips screwdriver
and
adjustable wrench
.
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of the manual. The number after the parentheses
shows the quantity needed for assembly.
Note: If a part is not in the parts bag, check to see if it is preat-
tached to one of the parts to be assembled. Extra hardware may be included. To avoid damaging plastic
parts, do not use power tools for assembly.
1.
Make sure that the power cord is unplugged.
With the help of a second person, carefully tip
the treadmill onto its left side. Partially fold the
Frame (53) so that the treadmill is more stable;
do not fully fold the Frame yet.
Remove and discard the two indicated bolts (A)
and the shipping bracket (B).
Cut the tie securing the Upright Wire (78) to the
Base (80). Locate the tie in the indicated hole in
the Base, and use the tie to pull the Upright Wire
out of the hole.
Attach a Base Pad (79) to the Base (80) in the
location shown with a Base Pad Spacer (25) and
a 1" Tek Screw (56). Then, attach another Base
Pad (79) with only a 1" Tek Screw (56).
80
56
53
79
3/8" Nut (8)–2
1" Tek Screw (56)–4
Base Pad Spacer
(25)–2
3/4" Screw (10)–5
3/8" Star
Washer (9)–4
5/16" Star
Washer (7)–4
5/16" x 1" Bolt (5)–4
3/8" x 2" Bolt (4)–2
3/8" x 4" Bolt (6)–4
1
79
56
78
Tie
Hole
A
B
25
6