ProForm 730 Sightline English Manual - Page 7

Caution

Get ProForm 730 Sightline PDF manuals and user guides View all ProForm 730 Sightline manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

DIAGRAM OF THE CONSOLE Monitor Displays LED Track Incline Control Clip Key Speed Control Pulse Sensor CAUTION: Before operating the console, read the following precautions. ¥ Do not stand on the walking belt when turning on the power. ¥ Always wear the clip while using the treadmill. When the key is removed from the console, the walking belt will stop. ¥ An emergency shut-off switch is built into the motor hood behind the walking belt. Any time that you step on the motor hood, the walking belt will stop. ¥ Adjust the speed in small increments. ¥ The settings marked above the speed control (warm-up/cool-down, fat burn, aerobic, and performance) are general guidelines only. See page 14 for more information. ¥ To reduce the possibility of electric shock, keep the console dry. Avoid spilling liquids on the console and use only a sealable water bottle. STEP BY STEP CONSOLE OPERATION If there is a thin sheet of clear plastic on the face of the console, remove it. Next, make sure that the power cord is properly plugged in (see HOW TO PLUG IN THE POWER CORD on page 7). Stand on the foot rails of the treadmill. Find the clip attached to the key (see the drawing above), and slide the clip onto the waistband of your clothing. Follow the steps below to operate the console. 1 Insert the key fully into the power switch. After a moment, the four displays and one indicator in the LED track will light. 2 Reset the speed control. Slide the speed control to the the RESET position. Note: Each time the walking belt is stopped, the speed control must be moved to the RESET position before the walking belt can be restarted. 3 Start the walking belt. Slowly slide the speed control to the right until the walking belt begins to move at slow speed. Step onto the walking belt. Change the speed of the walking belt as desired by sliding the speed control. To stop the walking belt, step onto the foot rails and slide the speed control to the RESET position. After a few seconds, the displays will pause. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
DIAGRAM OF THE CONSOLE
Pulse Sensor
Speed Control
Incline Control
Clip
Key
Monitor Displays
LED Track
CAUTION:
Before operating the
console, read the following precautions.
¥ Do not stand on the walking belt when turning
on the power.
¥ Always wear the clip while using the treadmill.
When the key is removed from the console, the
walking belt will stop.
¥
An emergency shut-off switch is built into the
motor hood behind the walking belt. Any time
that you step on the motor hood, the walking
belt will stop.
¥ Adjust the speed in small increments.
¥ The settings marked above the speed control
(warm-up/cool-down, fat burn, aerobic, and
performance) are general guidelines only. See
page 14 for more information.
¥ To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids on
the console and use only a sealable water
bottle.
STEP BY STEP CONSOLE OPERATION
If there is a thin sheet of clear plastic on the face of the
console, remove it. Next, make sure that the power
cord is properly plugged in (see HOW TO PLUG IN
THE POWER CORD on page 7).
Stand on the foot rails of the treadmill. Find the clip
attached to the key (see the drawing above), and
slide the clip onto the waistband of your clothing.
Follow the steps below to operate the console.
Insert the key fully into the power switch.
After a moment, the
four displays and one
indicator in the LED
track will light.
Reset the speed control.
Slide the speed
control to the
the RESET
position.
Note:
Each time the
walking belt is
stopped, the
speed control must be moved to the RESET po-
sition before the walking belt can be restarted.
Start the walking belt.
Slowly slide the speed control to the right until the
walking belt begins to move at slow speed. Step
onto the walking belt. Change the speed of the
walking belt as desired by sliding the speed control.
To stop the walking belt, step onto the foot rails
and slide the speed control to the RESET posi-
tion. After a few seconds, the displays will pause.
2
3
1
7