ProForm 764hr Bike Uk Manual - Page 7

Attach the Left Handlebar Bracket 88 to the Upright

Page 7 highlights

9. Attach the Left Handlebar Bracket (88) to the Upright (13) with two M6 x 32mm Button Screws (83) and two M6 Nylon Locknuts (45). Attach the Right Handlebar Bracket (95) to the Upright (13) in the same way. Do not tighten the Nylon Locknuts yet. Slide the Handlebar Collar (77) onto the Left Handlebar (11). Insert the Right Handlebar (15) into the Handlebar Collar. Connect the Handlebar Collar, the Left Handlebar, and the Right Handlebar with an M4 x 16mm Screw (73). Attach the Left Handlebar (11) to the Left Handlebar Bracket (88) with two M8 x 12mm Button Screws (94). Attach the Right Handlebar (15) to the Right Handlebar Bracket (95) in the same way. 10. The Console (16) requires four 1.5V "D" batteries; alkaline batteries are recommended. Remove the indicated screw from the battery drawer. Pull the battery drawer open and insert four batteries. Make sure that the batteries are oriented as shown by the markings inside of the battery drawer. Close the battery drawer and reattach the screw. Note: When the batteries are installed correctly, the fan will turn on for a moment. See step 9. Tighten the M6 Nylon Locknuts (45). 9 83 88 94 45 10 83 94 95 45 94 15 77 13 73 11 16 Batteries Screw Battery Drawer 11. Identify the Left Pedal (24), which is marked with an 11 "L." Using an adjustable wrench, firmly tighten the Left Pedal counterclockwise into the Left Crank Arm (42). Tighten the Right Pedal (not shown) clockwise into the Right Crank Arm (not shown) in the same way. Important: Tighten both Pedals as firmly as 25 possible. After using the crosstrainer for one week, retighten the Pedals. For the best perfor- mance, the Pedals must be kept properly tightened. Adjust the Left Pedal Strap (25) to the desired position and press the end of the Strap onto the tab on the Left Pedal (24). Adjust the Right Pedal Strap (not shown) in the same way. 24 42 Tab 12. Make sure that all parts of the crosstrainer are properly tightened. Note: Some hardware may be left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the crosstrainer. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

7
12.
Make sure that all parts of the crosstrainer are properly tightened.
Note: Some hardware may be left
over after assembly is completed. To protect the floor or carpet from damage, place a mat under the
crosstrainer.
10. The Console (16) requires four 1.5V ā€œDā€ batteries;
alkaline batteries are recommended. Remove the indi-
cated screw from the battery drawer. Pull the battery
drawer open and insert four batteries.
Make sure that
the batteries are oriented as shown by the mark-
ings inside of the battery drawer.
Close the battery
drawer and reattach the screw. Note: When the batter-
ies are installed correctly, the fan will turn on for a
moment.
See step 9. Tighten the M6 Nylon Locknuts (45).
11. Identify the Left Pedal (24), which is marked with an
ā€œL.ā€ Using an adjustable wrench,
firmly tighten
the
Left Pedal
counterclockwise
into the Left Crank Arm
(42). Tighten the Right Pedal (not shown)
clockwise
into the Right Crank Arm (not shown) in the same
way.
Important: Tighten both Pedals as firmly as
possible. After using the crosstrainer for one
week, retighten the Pedals. For the best perfor-
mance, the Pedals must be kept properly tightened.
Adjust the Left Pedal Strap (25) to the desired position
and press the end of the Strap onto the tab on the Left
Pedal (24). Adjust the Right Pedal Strap (not shown)
in the same way.
16
Batteries
Battery
Drawer
10
11
24
Tab
42
25
15
9.
Attach the Left Handlebar Bracket (88) to the Upright
(13) with two M6 x 32mm Button Screws (83) and two
M6 Nylon Locknuts (45). Attach the Right Handlebar
Bracket (95) to the Upright (13) in the same way. Do
not tighten the Nylon Locknuts yet.
Slide the Handlebar Collar (77) onto the Left
Handlebar (11). Insert the Right Handlebar (15) into
the Handlebar Collar. Connect the Handlebar Collar,
the Left Handlebar, and the Right Handlebar with an
M4 x 16mm Screw (73).
Attach the Left Handlebar (11) to the Left Handlebar
Bracket (88) with two M8 x 12mm Button Screws (94).
Attach the Right Handlebar (15) to the Right
Handlebar Bracket (95) in the same way.
9
13
77
73
88
11
45
83
94
95
94
94
45
83
Screw