ProForm 785xt Treadmill User Manual - Page 6

ProForm 785xt Treadmill Manual

Page 6 highlights

4. Move your right hand to the position shown at the right, and hold the treadmill firmly. Using your left hand, lift the storage latch. Raise the treadmill until the locking pin snaps into the storage latch. Make sure that the locking pin is inside the storage latch, and that the storage latch is fully closed. 4 Storage Latch Locking Pin 5. Stand behind the treadmill. Hold the Right Crossbar Bracket (51) and the Left Crossbar Bracket (not shown). 5 51 Place one foot on the base in the indicated location. Tip the treadmill back slightly. While the treadmill is held in this position, a second person should slide the Stabilizer Plate (88) onto the base (see the inset drawing). Keeping your foot on the base, carefully tip the treadmill up until it is resting on the base. Make sure that the Stabilizer Plate (88) stays on the base. 88 . Attach the Stabilizer Plate (88) to the base with a Stabilizer Plate Bolt (105), two Stabilizer Plate Washers (97), and the Stabilizer Plate Nut (95) as shown. Base 97 95 , 105 88 6. See assembly step 4. Hold the upper end of the treadmill with your right hand as shown. Using your left hand, lift 6 the storage latch. Pivot the treadmill slightly until the lock- ing pin is out of the storage latch. _ Hold the treadmill firmly with both hands, and lower the treadmill to the floor. To decrease the possibility of in- ( I jury, bend your legs and keep your back straight. ° 7. Remove the paper backing from the Adhesive Clip (44). Press the Adhesive Clip onto the Frame (84) in the indi- 7 cated location. Press the 3/16" Allen Wrench (57) into the Adhesive Clip. The use of the 3/16" Allen Wrench is de- scribed on page 21. 6 44 57 84

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27

4.
Move
your
right
hand
to
the
position
shown
at
the
right,
and
hold
the
treadmill
firmly.
Using
your
left
hand,
lift
the
storage
latch.
Raise
the
treadmill
until
the
locking
pin
snaps
into
the
storage
latch.
Make
sure
that
the
locking
pin
is
inside
the
storage
latch,
and
that
the
storage
latch
is
fully
closed.
5.
Stand
behind
the
treadmill.
Hold
the
Right
Crossbar
Bracket
(51)
and
the
Left
Crossbar
Bracket
(not
shown).
Place
one
foot
on
the base
in
the
indicated
location.
Tip
the
treadmill
back
slightly.
While
the
treadmill
is
held
in
this
position,
a
second
person
should
slide
the
Stabilizer
Plate
(88) onto
the
base
(see
the
inset
draw-
ing).
Keeping
your
foot
on
the
base,
carefully
tip
the
treadmill
up
until
it
is
resting
on
the
base.
Make
sure
that
the
Stabilizer
Plate
(88)
stays
on
the
base.
Attach
the
Stabilizer
Plate
(88)
to
the
base
with
a
Stabilizer
Plate
Bolt
(105),
two
Stabilizer
Plate
Washers
(97),
and
the
Stabilizer
Plate
Nut
(95)
as
shown.
6.
See
assembly
step
4.
Hold
the
upper
end
of
the
treadmill
with
your
right
hand
as
shown.
Using
your
left
hand,
lift
the
storage
latch.
Pivot
the
treadmill
slightly
until
the
lock-
ing
pin
is
out
of
the
storage
latch.
_
Hold
the
treadmill
firmly
with
both
hands,
and
lower the
treadmill
to
the
floor.
To
decrease
the
possibility
of
in-
jury,
bend
your
legs
and
keep
your
back
straight.
7.
Remove
the
paper
backing
from
the
Adhesive
Clip
(44).
Press
the
Adhesive
Clip
onto
the
Frame
(84)
in
the
indi-
cated
location.
Press
the
3/16"
Allen
Wrench
(57)
into
the
Adhesive
Clip.
The
use
of
the
3/16"
Allen
Wrench
is
de-
scribed
on
page
21.
6
4
Storage
Latch
Locking
Pin
5
88
Base
51
.
105
97
88
9
5
,
6
(
I
°
7
44
57
84
-
'''''''''-,