ProForm 995 Sel Treadmill English Manual - Page 6

Assembly - lubrication

Get ProForm 995 Sel Treadmill PDF manuals and user guides View all ProForm 995 Sel Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

ASSEMBLY Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires your own phillips screw- driver and rubber mallet . Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. 1. With the help of a second person, carefully raise the treadmill to the upright position as shown. 1 While a second person tips the treadmill to one side and holds it, insert one of the Extension Legs (102) into the treadmill as shown. Make sure that the Extension Leg is turned so the Base Pad (99) is on the bottom. Next, tip the treadmill to the other side and insert the other Extension Leg (not shown) in the same way. Lower the side of the treadmill so that both Extension Legs (102) are resting flat on the floor. 102 99 2. With the help of a second person, carefully lower the treadmill frame and then tip the Uprights (69) down as 2 shown. Make sure that the Extension Legs (102) remain in the Uprights. Attach each Extension Leg (102) with two of the six 3/4" Screws (100) as shown. With the help of a second person, carefully tip the Uprights (69) back to the vertical position. 69 Note: One replacement Base Pad (99) may be included. Use the extra Base Pad if one becomes worn or needs to be replaced. 99 99 Frame 100 102 69 100 102 3. Insert a Handrail Extension (66) into the post on the right Upright (69) as shown; make sure that the indicated holes are on top. Tap the Handrail Extension with a rubber mallet to fully insert it. Attach the Handrail Extension with two 1/2" Screws (67) as shown. Identify the Right Foam Grip (75), which has a large cutout in the left side for the Pulse Bar (76). Slide the Right Foam Grip as far as possible onto the post on the right Upright (69). (Note: It may be helpful to apply soapy water to the Handrail Extension [66].) Make sure that the tab on the Foam Grip is inserted into the Console Base (81). 3 76 Tab 67 Cutout Holes 75 66 81 69 Post 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
ASSEMBLY
Assembly requires two people.
Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Assembly requires your own phillips screw-
driver
and rubber mallet
.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
2.
With the help of a second person, carefully lower the
treadmill frame and then tip the Uprights (69) down as
shown.
Make sure that the Extension Legs (102) remain
in the Uprights.
Attach each Extension Leg (102) with two of the six 3/4”
Screws (100) as shown.
With the help of a second person, carefully tip the
Uprights (69) back to the vertical position.
Note: One replacement Base Pad (99) may be included.
Use the extra Base Pad if one becomes worn or needs to
be replaced.
100
102
69
99
99
Frame
69
100
102
1.
With the help of a second person, carefully raise the
treadmill to the upright position as shown.
While a second person tips the treadmill to one side
and holds it, insert one of the Extension Legs (102) into
the treadmill as shown. Make sure that the Extension
Leg is turned so the Base Pad (99) is on the bottom.
Next, tip the treadmill to the other side and insert the
other Extension Leg (not shown) in the same way. Lower
the side of the treadmill so that both Extension Legs
(102) are resting flat on the floor.
102
99
1
3.
Insert a Handrail Extension (66) into the post on the right
Upright (69) as shown; make sure that the indicated holes
are on top. Tap the Handrail Extension with a rubber mallet
to fully insert it. Attach the Handrail Extension with two 1/2”
Screws (67) as shown.
Identify the Right Foam Grip (75), which has a
large
cutout
in the left side for the Pulse Bar (76). Slide the Right Foam
Grip as far as possible onto the post on the right Upright
(69). (Note: It may be helpful to apply soapy water to the
Handrail Extension [66].) Make sure that the tab on the
Foam Grip is inserted into the Console Base (81).
75
76
Cutout
Tab
66
Post
67
Holes
69
81
3
2
6