ProForm Crosswalk 375 E Treadmill English Manual - Page 8

Console May Be Damaged When

Get ProForm Crosswalk 375 E Treadmill PDF manuals and user guides View all ProForm Crosswalk 375 E Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

5. Set the Console (43) face down on a soft surface to avoid scratching the Console. Next, set one of the Handrails (71) on the Console as shown. Attach the Handrail with three 3/4" Screws (2). Make sure that the console wire is not pinched. Start all three Screws before tightening any of them. Do not overtighten the Screws. Then, attach the other Handrail (not shown) to the other side of the Console (43) as described above. With the help of a second person, raise the Uprights (not shown) to the vertical position. 6. Remove the plastic tie holding the Wire Harness (42) to the right Upright (69). Insert the colored tie on the Wire Harness up through the large holes in the right Handrail (71) as shown. Pull the Wire Harness up through the holes. Next, set the Handrails (71) with the Console (43) onto the tops of the Uprights (69). Make sure that the Wire Harness (42) and the console wire are not pinched. Untie and discard the colored wire. Then, connect the Wire Harness (42) to the console wire. Make sure to connect the connectors properly (see the inset drawing). The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Insert the connectors and excess wire into the Console (43). 7. Tighten the four Handrail Bolts (37) with the four 1/4" Star Washers (95) into the Uprights (69) and the Handrails (71). Start all four Bolts before tightening any of them. 5 71 Console Wire 43 2 2 2 6 43 71 Colored Tie Console Wire Console 42 Wire 42 69 7 71 37 95 37 95 69 71 95 37 37 95 69 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
8
7.
Tighten the four Handrail Bolts (37) with the four
1/4” Star Washers (95) into the Uprights (69) and
the Handrails (71).
Start all four Bolts before
tightening any of them.
95
37
95
37
71
71
95
69
69
37
7
5.
Set the Console (43) face down on a soft surface
to avoid scratching the Console. Next, set one of
the Handrails (71) on the Console as shown.
Attach the Handrail with three 3/4” Screws (2).
Make sure that the console wire is not
pinched. Start all three Screws before tight-
ening any of them. Do not overtighten the
Screws.
Then, attach the other Handrail (not shown) to
the other side of the Console (43) as described
above.
With the help of a second person, raise the
Uprights (not shown) to the vertical position.
71
43
Console Wire
5
2
2
2
6.
Remove the plastic tie holding the Wire Harness
(42) to the right Upright (69). Insert the colored
tie on the Wire Harness up through the large
holes in the right Handrail (71) as shown. Pull
the Wire Harness up through the holes.
Next, set the Handrails (71) with the Console
(43) onto the tops of the Uprights (69).
Make
sure that the Wire Harness (42) and the con-
sole wire are not pinched.
Untie and discard
the colored wire.
Then, connect the Wire Harness (42) to the con-
sole wire.
Make sure to connect the connec-
tors properly (see the inset drawing). The
connectors should slide together easily and
snap into place.
If the connectors do not slide
together easily and snap into place, turn one
connector and try again.
IF THE CONNECTORS
ARE NOT CONNECTED PROPERLY, THE
CONSOLE MAY BE DAMAGED WHEN THE
POWER IS TURNED ON.
Insert the connectors
and excess wire into the Console (43).
69
42
43
6
42
95
37
71
Console
Wire
Colored Tie
Console
Wire