ProForm L18 Treadmill English Manual - Page 5

Assembly

Get ProForm L18 Treadmill PDF manuals and user guides View all ProForm L18 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

ASSEMBLY Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench and your own phillips screwdriver and adjustable wrench . 1. With the help of a second person, carefully raise the treadmill to the upright position. While a second person tips the treadmill to one side and holds it, insert one of the Extension Legs (103) into the treadmill as shown. Make sure that the Extension Leg is turned so the Warning Decal (20) is on top. Next, tip the treadmill to the other side and insert the other Extension Leg (not shown) in the same way. Lower the side of the treadmill so that both Extension Legs (103) are resting flat on the floor. 1 20 103 2. Refer to HOW TO LOWER THE TREADMILL FOR USE on page 10. Follow the instructions in step 2 to lower the treadmill. Attach the latch support to the center hole in the left Upright (82) with a 3/4Ó Screw (81). Make sure that the Screw is tight, but do not overtighten it; if the Screw is overtightened, the latch will not slide smoothly. Remove the tape from the Latch Assembly (77). Be careful to hold the parts in place. Inset drawing (a) shows how the Latch Assembly fits together. Refer to inset drawing (b). Insert the springs into the bracket as shown. Make sure the tabs are touching the bracket and the back end of the latch is flush with the bracket. Attach the Latch Assembly (77) to the left Upright (82) with two 3/4Ó Screws (81). 3. Slide the upper end of a Handrail (75) onto the right Upright (82) as shown. Note: It will be necessary to pivot the Handrail to the side and back repeatedly (see arrow A) while pushing on the Handrail (see arrow B) to slide it fully onto the Upright. Next, pivot the lower end of the Handrail down, push it toward the right Upright, and then align it with the indicated hole. Slide the other Handrail (75) onto the left Upright (82) as described above. 2 82 81 77 81 Latch Support a Bracket Latch b Spring Flush Spring Tabs 3 B 82 75 82 75 A Hole 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
5
1.
With the help of a second person, carefully raise the
treadmill to the upright position. While a second person
tips the treadmill to one side and holds it, insert one of
the Extension Legs (103) into the treadmill as shown.
Make sure that the Extension Leg is turned so the
Warning Decal (20) is on top.
Next, tip the treadmill to the other side and insert the
other Extension Leg (not shown) in the same way. Lower
the side of the treadmill so that both Extension Legs
(103) are resting flat on the floor.
20
103
1
2.
Refer to HOW TO LOWER THE TREADMILL FOR USE
on page 10. Follow the instructions in step 2 to lower
the treadmill.
Attach the latch support to the center hole in the left
Upright (82) with a 3/4± Screw (81).
Make sure that the
Screw is tight, but do not overtighten it; if the Screw
is overtightened, the latch will not slide smoothly.
Remove the tape from the Latch Assembly (77).
Be
careful to hold the parts in place.
Inset drawing (a)
shows how the Latch Assembly fits together. Refer to
inset drawing (b). Insert the springs into the bracket as
shown. Make sure the tabs are touching the bracket
and the back end of the latch is flush with the bracket.
Attach the Latch Assembly (77) to the left Upright (82)
with two 3/4± Screws (81).
ASSEMBLY
Assembly requires two people.
Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Assembly requires the included allen wrench
and your own phillips screwdriver
and adjustable wrench
.
3.
Slide the upper end of a Handrail (75) onto the right
Upright (82) as shown.
Note: It will be necessary to
pivot the Handrail to the side and back repeatedly
(see arrow A) while pushing on the Handrail (see
arrow B) to slide it fully onto the Upright.
Next, pivot
the lower end of the Handrail down,
push it toward the
right Upright
, and then align it with the indicated hole.
Slide the other Handrail (75) onto the left Upright (82) as
described above.
82
75
75
82
Hole
3
B
A
77
81
81
82
2
Flush
Bracket
a
b
Latch
Support
Latch
Spring
Spring
Tabs