ProForm Lx360 Treadmill English Manual - Page 5

Assembly - used

Get ProForm Lx360 Treadmill PDF manuals and user guides View all ProForm Lx360 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly requires the included allen wrenches and your own phillips screwdriver , 9/16" wrench , wire cutters , and needlenose pliers . To identify small parts during assembly, use the PART IDENTIFICATION CHART in the center of this manual. 1. Make sure that the power cord is unplugged. 1 86 57 58 69 57 With the help of a second person, carefully tip the 58 treadmill onto its left side as shown. Partially fold the Frame (86) so that the treadmill is more stable. Do not fully fold the treadmill until it is completely assem- bled. Attach four Base Pads (57) to the bottom of the Base (69) with four 1" Tek Screws (58) (three are shown). 58 57 2. Hold one of the Uprights (73) near the Base (69), with the holes on the indicated side. Straighten the Wire Harness (42), and feed it into the lower end of the Upright and out of the large hole near the upper end. Insert two 2 1/2" Bolts (37) with 3/8" Star Washers (38) into the bottom of the Base (69) and the lower end of the Upright (73); be careful not to damage the Wire Harness (42). Firmly tighten an Upright Nut (109) onto each Upright Bolt. Attach the other Upright (not shown) as described above. Note: There is not a wire harness on the left side. Refer to the inset drawing. Clip two U-nuts (108) over the two round holes in each of the Uprights (73) as shown. Press an Upright Endcap (107) onto the top of each Upright. Note: Make sure the angle of the ends of the Endcap matches the angle of the Upright. 5 2 42 Holes 109 69 73 109 37 38 107 108 37 38 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
ASSEMBLY
Assembly requires two persons.
Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included allen wrenches
and your own phillips screwdriver
,
9/16” wrench
, wire cutters
, and needlenose pliers
.
To identify small parts during assembly, use the PART IDENTIFICATION CHART in the center of this manual.
1.
Make sure that the power cord is unplugged.
With the help of a second person, carefully tip the
treadmill onto its left side as shown. Partially fold the
Frame (86) so that the treadmill is more stable.
Do not
fully fold the treadmill until it is completely assem-
bled.
Attach four Base Pads (57) to the bottom of the Base
(69) with four 1” Tek Screws (58) (three are shown).
2.
Hold one of the Uprights (73) near the Base (69),
with
the holes on the indicated side.
Straighten the Wire
Harness (42), and feed it into the lower end of the Upright
and out of the large hole near the upper end.
Insert two 2 1/2” Bolts (37) with 3/8” Star Washers (38)
into the bottom of the Base (69) and the lower end of the
Upright (73);
be careful not to damage the Wire
Harness (42).
Firmly tighten an Upright Nut (109) onto
each Upright Bolt.
Attach the other Upright (not shown) as described
above. Note: There is not a wire harness on the left side.
Refer to the inset drawing. Clip two U-nuts (108) over
the two round holes in each of the Uprights (73) as
shown. Press an Upright Endcap (107) onto the top of
each Upright. Note: Make sure the angle of the ends of
the Endcap matches the angle of the Upright.
42
Holes
69
109
38
37
73
109
2
37
38
5
57
58
58
57
57
69
86
1
108
107
73
58