Pyle PDWM3300 PDWM3300 Manual 1 - Page 2

FUNCTION INTRODUCTION, MAIN FUNCTION, OPERATION OF THE RECEIVER, Attention, install, receiver, IY. - wireless professional uhf

Get Pyle PDWM3300 PDF manuals and user guides View all Pyle PDWM3300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

I .FUNCTION INTRODUCTION Our special wireless microphone system has these characteristics as the following. For many reasons, such as low frequency, tradional wireless microphone system are easy to be interfered especially because many machines CD, VCD and LD, erad-iate out too many harmonic. To solve this problem we design this kind professional wireless microphone We adopt a series of measures to inprove its functions, advance frequency, using multilevel high frequency and mid frequency narrowband filter, mulriple noise detect and control We also design it special functions (tone key locked identity) to avoid interference from outside. II. MAIN FUNCTION ""Using UHF 793.l-822.8MHz band to avoid interferencing frequency. ""Using multilevel high frequency and mid frequency narrowband filter, so as to dispel any possible interferencing signals. ""The wireless microphone look good and are useful. ""There is a volt indicating circuit in the microphone. It can tell you if it is necessary to change the battery. ""A specially designed circuit switch is on the phone. It is for clearing up waves of miscellaneous signals. ""All use SMT technology for PCB. ""With audio compressing-expanding technology, the machine can lower noise and increase the dynamic range. It can also lower reecho. ""Particular noise detect to avoid interference from outside open the mute system. ""Choose excellent chipset and high quality component, so that its timbre is very good. ""Longest distance in oopen:80m. Idealest, distance in open:50m. ""It is suitable for stages ballrooms auditoria classrooms and families. III. OPERATION OF THE RECEIVER 1.lnstall the antenna A&B, make them be perpendicular with the machine. 2.lnstall adapter to the DC input. 3.Connection ofthe audio output: One end of the audio cable into "MIX"socket and other end audio amplifier or mixer's "MIC IN" socket. 1 4.Push the power switch, the power-indicating light is lighted. 5.when the microphone is working the "SIGNAL"light ofthe receiver is lighted. The receiver output voice, volume of the receiver can be controlled by adjusting the volume knob. *Attention when you install the receiver *It should be more than 1 metre high from the floor. *It should be more than 1 metre beyond the wall. *Antennas should be put out fully, otherwise it'll influence receiving signals. IY.OPERATION OF THE MICROPHONE 1.0pen the battery cover,then put in the battery.Attention:The polarity should be right. 2.Tum on the microphone and make sure the frequency showing same as receiver. If low voltage the screen will show "LBAT",then off itself. 3.Press the power button 1 or 2 second then it will off. V. CONTROL AND FUNCTION LlST(Receiver) 2

  • 1
  • 2
  • 3
I
.FUNCTION INTRODUCTION
Our
special wireless microphone system has these characteristics
as
the
following. For many reasons, such as low frequency, tradional wireless microphone
system are easy to be interfered especially because many machines CD, VCD and
LD, erad-iate out too many harmonic.
To
solve this problem we design this kind
professional wireless microphone
We
adopt a series
of
measures to inprove its
functions, advance frequency, using multilevel high frequency and mid frequency
narrowband filter, mulriple noise detect and control We also design it special
functions (tone key locked identity) to avoid interference from outside.
II.
MAIN FUNCTION
""Using
UHF
793.l-822.8MHz
band
to
avoid interferencing frequency.
""Using
multilevel high frequency and mid frequency narrowband filter, so
as
to
dispel
any
possible interferencing signals.
""The
wireless microphone look good and are useful.
""There
is a volt indicating circuit
in
the microphone. It can tell you
if
it is necessary
to change the battery.
""A
specially designed circuit switch is on the phone. It is
for
clearing up waves
of
miscellaneous signals.
""All
use
SMT
technology
for
PCB.
""With
audio compressing-expanding technology, the machine can lower noise
and increase the dynamic range. It can also lower reecho.
""Particular
noise detect to avoid interference from outside open the mute system.
""Choose
excellent chipset and high quality component, so that its timbre is very
good.
""Longest
distance
in
oopen:80m. Idealest, distance in open:50m.
""It
is suitable
for
stages ballrooms auditoria classrooms and families.
III.
OPERATION OF THE RECEIVER
1.lnstall the antenna A&B, make them be perpendicular with the machine.
2.lnstall adapter to the DC input.
3.Connection
ofthe
audio output:
One end
of
the audio cable into "MIX"socket and other end audio amplifier
or
mixer's "MIC IN" socket.
1
4.Push the power switch, the power-indicating light is lighted.
5.when
the microphone is working the "SIGNAL"light
ofthe
receiver is lighted.
The receiver output voice, volume
of
the receiver can be controlled by
adjusting the volume knob.
*Attention
when
you
install
the
receiver
*It
should be more than 1 metre high from the floor.
*It
should be more than 1 metre beyond the wall.
*Antennas
should be put
out
fully, otherwise it'll influence receiving signals.
IY.OPERATION
OF
THE MICROPHONE
1.0pen the battery cover,then put
in
the battery.Attention:The polarity should be
right.
2.Tum on the microphone and make sure the frequency showing same as receiver.
If low voltage the screen will show "LBAT",then off itself.
3.Press the power button 1
or
2 second then it will off.
V. CONTROL AND FUNCTION LlST(Receiver)
2