Pyle PLAD3300D PLAD3300D Manual 1 - Page 7

conditions

Get Pyle PLAD3300D PDF manuals and user guides View all Pyle PLAD3300D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

FERTURES € CONTROLS 11. LED Indicator - POWER : This GREEN LED will illuminate when the amplifier is turned "ON". If it fails to illuminate, check the power connections to the Amplifier and fuses. - PROTECTION : The amplifier protection circuitry will disable the amplifier if input overload, short circuit or extremely high temperature conditions are detected. When the protection mode is in operation, the LED indicator on the side panel will be illuminated, indicating the amplifier has gone into a self preservation mode. If you observe that the Protection LED is lit, please check the system carefully to determine what has caused the protection circuit to engage. The amplifier can be reset by turning the remote power off and then on again. If the amplifier shut down due to a thermal overload condition, please allow it to cool down before restarting. If the amplifier shut down because of an input overload or short circuit, be sure to repair these conditions before attempting to power up the amplifier again. 12. B- TERMINAL (CHASSIS GROUND) To avoid unwanted ignition noise caused by ground loops, it is essential that the Amplifier be grounded to a clean, bare, metal surface of the vehicles chassis. 13. REMOTE POWER ON To remote wire car stereo. This amplifier is turned "ON" remotely when vehicle's stereo is turned "ON". Note: IF YOUR RADIO DOES NOT HAVE +12 VOLT OUTPUT LEAD WHEN TURNED ON, THE "REMOTE" TERMINAL ON THE AMPLIFIER CAN BE CONNECTED TO VEHICLES ACCESSORY CIRCUIT WHICH PROVIDES +12V WHEN THE CAR IS ON. 14.B+ TERMINAL (BATTERY POSITIVE) Due to the power requirements of the Amplifier, this connection should be made directly to the positive(+) terminal of battery. For safety measure, install an in-line fuse Holder (not included) as close to the battery positive(+) terminal as possible with an ampere rating not to exceed total value of fuses in Amp. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
FERTURES
€
CONTROLS
11.
LED
Indicator
-
POWER
:
This
GREEN
LED
will
illuminate
when
the
amplifier
is
turned
"ON".
If
it
fails
to
illuminate,
check
the
power
connections
to
the
Amplifier
and
fuses.
-
PROTECTION
:
The
amplifier
protection
circuitry
will
disable
the
amplifier
if
input
overload,
short
circuit
or
extremely
high
temperature
conditions
are
detected.
When
the
protection
mode
is
in
operation,
the
LED
indicator
on
the
side
panel
will
be
illuminated,
indicating
the
amplifier
has
gone
into
a
self
preservation
mode.
If
you
observe
that
the
Protection
LED
is
lit,
please
check
the
system
carefully
to
determine
what
has
caused
the
protection
circuit
to
engage.
The
amplifier
can
be
reset
by
turning
the
remote
power
off
and
then
on
again.
If
the
amplifier
shut
down
due
to
a
thermal
overload
condition,
please
allow
it
to
cool
down
before
restarting.
If
the
amplifier
shut
down
because
of
an
input
overload
or
short
circuit,
be
sure
to
repair
these
conditions
before
attempting
to
power
up
the
amplifier
again.
12.
B-
TERMINAL
(CHASSIS
GROUND)
To
avoid
unwanted
ignition
noise
caused
by
ground
loops,
it
is
essential
that
the
Amplifier
be
grounded
to
a
clean,
bare,
metal
surface
of
the
vehicles
chassis.
13.
REMOTE
POWER
ON
To
remote
wire
car
stereo.
This
amplifier
is
turned
"ON"
remotely
when
vehicle's
stereo
is
turned
"ON".
Note:
IF
YOUR
RADIO
DOES
NOT
HAVE
+12
VOLT
OUTPUT
LEAD
WHEN
TURNED
ON,
THE
"REMOTE"
TERMINAL
ON
THE
AMPLIFIER
CAN
BE
CONNECTED
TO
VEHICLES
ACCESSORY
CIRCUIT
WHICH
PROVIDES
+12V
WHEN
THE
CAR
IS
ON.
14.B+
TERMINAL
(BATTERY
POSITIVE)
Due
to
the
power
requirements
of
the
Amplifier,
this
connection
should
be
made
directly
to
the
positive(+)
terminal
of
battery.
For
safety
measure,
install
an
in
-line
fuse
Holder
(not
included)
as
close
to
the
battery
positive(+)
terminal
as
possible
with
an
ampere
rating
not
to
exceed
total
value
of
fuses
in
Amp.
6