Pyle PLCM46 User Manual - Page 3

Quick Installation, Camera Connection, Display Monitor Connection

Page 3 highlights

 SystemInstallationandWiring Note:CameraSysteminstallationondieselvehiclesmayrequireaslightlydifferentwiringinstall.    Caution: Connecting to other types of electrical systems will cause damage to your vehicle. Please contact the manufacturer if you are  unawareofthesystemtypeinyourvehicle.Refertothemodel'spowerrequirementspriortoconnectionandinstallation.    QuickInstallation: This rearview backup camera system comes in two parts, one is the camera, the other is the monitor. When installing,thecameracanbemountedeitherintherearofyourvehicle(preferablyjustabovethelicenseplate) orinfrontofyourvehicle(also,preferablyjustabovethelicenseplate).  Thiskitincludesnecessarywiringandcableconnectoraccessoriessufficientfortypicalconnections. However, additional accessory cables and installation materials may be necessary for a completely secureandoperationalbackupcameraperformance.  CameraConnection: Connect the camera, using the red wire, of the included DC 12V power cable, to the positive 12V reverse tail lightintherearofyourcar.Then,connecttheblackwire,oftheDC12Vpowercable,makingsuretoground properly. This connected power and ground cable then connects to the camera, and will supply power to the cameradirectly. Next, use the included yellow RCA video connector cable, and run that cable from the yellow RCA video connectorjackofthecamera,totheyellowvideoconnectoroftheincludeddisplaymonitor. DisplayMonitorConnection: Connectthemonitor,usingtheredwire,oftheotherincludedDC12Vpowercable.Connectthiswiretoyour vehicle'sfusepaneltoprovidepowertothemonitor.ThenconnecttheblackwireoftheDC12Vcablemaking suretheconnectingisgroundedproperly.    The additional video input on the monitor (white cable) is available for connecting an additional monitor or displayscreen.Theincludeddisplaymonitorassembly,whenconnected,automaticallyretrievesthevideosignal whenactivated.   

  • 1
  • 2
  • 3
  • 4
  • 5

System Installation and Wiring
Note: Camera System installation on diesel vehicles
may
require a slightly different wiring install.
Quick Installation:
This rearview backup camera system comes in two parts, one is the camera, the other is the monitor. When
installing, the camera can be mounted either in the rear of your vehicle (preferably just above the license plate)
or in front of your vehicle (also, preferably just above the license plate).
This kit includes necessary wiring and cable connector accessories sufficient for typical connections.
However, additional accessory cables and installation materials may be necessary for a completely
secure and operational backup camera performance.
Camera Connection:
Connect the camera, using the red wire, of the included DC 12V power cable, to the positive 12V reverse tail
light in the rear of your car. Then, connect the black wire, of the DC 12V power cable, making sure to ground
properly. This connected power and ground cable then connects to the camera, and will supply power to the
camera directly.
Next, use the included yellow RCA video connector cable, and run that cable from the yellow RCA video
connector jack of the camera, to the yellow video connector of the included display monitor.
Display Monitor Connection:
Connect the monitor, using the red wire, of the other included DC 12V power cable. Connect this wire to your
vehicle's fuse panel to provide power to the monitor. Then connect the black wire of the DC 12V cable making
sure the connecting is grounded properly.
The additional video input on the monitor (white cable) is available for connecting an additional monitor or
display screen. The included display monitor assembly, when connected, automatically retrieves the video signal
when activated.
Caution: Connecting to other types of electrical systems will cause damage to your vehicle. Please contact the manufacturer if you are
unaware of the system type in your vehicle. Refer to the model's power requirements prior to connection and installation.