RCA DRC288SU DRC288SU Product Manual - Page 1
RCA DRC288SU Manual
UPC - 062118428800
View all RCA DRC288SU manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
User manual DRC288SU It is important to read this instruction prior to using your new product for the first time. Safety Precautions Caution Marking and rating plate was located at rear enclosure of the apparatus. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with an arrowhead symbol, within the equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to cause an electric shock. The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in this user manual. CAUTION INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM. WARNING: THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON APPARATUS. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE. CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE. CAUTION: TO REDUCE THE RISK OF FIRE, DO NOT PLACE ANY HEATING OR COOKING APPARATUS BENEATH THIS UNIT. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT OF POWER OUTLET, THEN FULLY INSERT. THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. The symbol for Class II (Double Insulation) This product contains a low power laser device. On Placement • Do not use the unit in places that are extremely hot, cold, dusty, or humid. • The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table-cloths, curtains, etc. On Safety • When connecting or disconnecting the AC power cord, grip the plug and not the cord itself. Pulling the cord may damage it and create a hazard. • When you are not going to use the unit for a long period of time, disconnect the AC power cord. • No naked flame sources such as lighted candles should be placed on the AC power cord and the unit. • Leave a minimum of 10cm around the apparatus for ventilation. • Attention should be drawn to the environmental aspects of battery disposal. • Use of apparatus in moderate climates. On Condensation • When left in a heated room where it is warm and damp, water droplets or condensation may form inside the unit. When there is condensation inside the unit, the unit may not function normally. Let the unit stand for 1 to 2 hours before turning the power on, or gradually heat the room and let the unit dry before use. Rating Plate Location • The rating plate is located on the back of unit. FCC Statements NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This unit has earned the ENERGY STAR. • • WARNING Should any trouble occur, disconnect the AC power cord and refer servicing to a qualified technician. Main plug is used as the disconnect device, it shall remain readily operable and should not be obstructed during intended use. To be completely disconnected the apparatus from supply mains, the main plug of the apparatus shall be disconnected from the mains socket outlet completely. Notes on Copyright It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted material without permission. This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited. - 1 - IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your AC power outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the AC power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. Portable Cart Warning 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the AC power cord or plug is damaged, liquid has spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Disc Formats The unit can playback: DVDs [8cm/12cm disc] Audio CDs [8cm/12cm disc] Compatible Region Management Information This unit is designed and manufactured to respond to the Region Management Information that is encoded on DVDs. If the region number printed on the DVD does not correspond to the region number of this unit, it cannot play that disc. The region number of this unit is 1. Disc Function or Operation that is Not Available When the appears on the screen, it indicates that the function or operation attempted is not available at that time. This occurs because the DVD manufacturer determines the specific functions of DVDs. Certain functions may not be available on some DVDs. Be sure to read the documentation provided with the DVD. Icons Used on DVDs Sample lcons Language selections for audio Language selections for subtitles Screen aspect ratio Multiple camera angles Region code indicator Notes on Unauthorized Discs You may not be able to play some DVDs on this unit, particularly if they were purchased from outside your geographic area or made for business purposes. Note: When playing back a CD-G (Graphics) or CD EXTRA disc, the audio portion will be played, but the graphic images will not be shown. Title, Chapter and Tracks • DVDs are divided into "titles" and "chapters". If the disc has more than one movie on it, each movie would be a separate "title". "Chapters" are sections of titles. • Audio CDs are divided into "tracks". A "track" is usually one song on an Audio CD. Note: Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded on them, but some do not. sound system Dolby Digital Dolby Digital is a technology developed by Dolby Laboratories. Soundtracks encoded in Dolby Digital can reproduce from one to 5.1 discrete channels of excellent quality audio. The unit automatically recognizes the Dolby Digital bitstream and provides a downmix suitable for two-channel listening. An additional Dolby Digital decoder is required for reproduction of the discrete multi-channel soundtracks available on many DVDs. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. ACCESSORIES Please check and identify the supplied accessories. • To order accessories, visit web site http://www.RCAav.com Remote Control ...x 1 2xAAA batteries...x 1 AV cable...x 1 - 2 - remote control Using the Remote Control • Point the remote control at the REMOTE SENSOR located on the unit. • When using this unit in very bright light, the infrared REMOTE CONTROL SENSOR may not work properly. • The recommended effective distance for remote operation is about 16 feet (5 meters). Battery Replacement When the batteries become weak, the operating distance of the remote control will be greatly reduced and you will need to replace the batteries. To Change Remote Batteries 1. Open the battery door. 2. Insert two AAA size batteries. Note: • If the remote control is not going to be used for a long time, remove the batteries to avoid damage caused by battery leakage corrosion. • When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be strictly followed. • Do not mix old and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC), or rechargeable (Ni-Cd, Ni-MH, etc) batteries. WARNING: • Do not dispose of the battery in fire or it may explode or leak. • Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. maintenance Cleaning the Disc A defective or soiled disc inserted into the unit can cause sound to drop out during playback. Handle the disc by holding its inner and outer edges. • Do NOT touch the surface of the unlabeled side of the disc. • Do NOT stick paper or tape on the surface. • Do NOT expose the disc to direct sunlight or excessive heat. • Clean the disc before playback. Wipe the disc from the center outward with a cleaning cloth. • NEVER use solvents such as benzine or alcohol to clean the disc. • Do NOT use irregular shaped discs (example: heart shaped, octagonal, etc.). They may cause malfunctions. Cleaning the Unit • Be sure to turn the unit off and disconnect the AC power cord before maintaining the unit. • Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth that has been dipped in a weak soap-and-water solution and wrung out thoroughly, then wipe with a dry cloth. • Never use alcohol, benzine, thinner, cleaning fluid or other chemicals. Do NOT use compressed air to remove dust. Important Note Before transporting the unit, remove the disc from the disc compartment. troubleshooting guide SYMPTOM CAUSE (AND REMEDY) No power. The remote control does not function. No sound or only a very low-level sound is heard. No picture or abnormal color. • Ensure the AC power cord is connected. • The unit is not turned on. • Remove any obstacles between the remote and the unit • Use the remote near the unit. • Point the remote at the remote sensor on the unit. • Replace the batteries in the remote with new one. • Make sure that you select ON mode. • The system is in pause mode. Press the PLAY button to return to normal play mode. • The unit is in fast-forward or fast-reverse mode. Press the PLAY button to return to normal play mode. • Make sure the AUDIO output is correct. • Make sure the audio cable is connected securely. • The region number of the disc doesn't match the region number of this unit. No output on your HDMI TV. Severe hum or noise is heard. The disc does not play. Video file won't play on device The DVD door cannot open. • The TV is not set to receive DVD signal output. • The video/HDMI cable is not connected securely. • The TV is not turned on. • Clean the disc. • Check connection between HDMI TV and the unit. • Replace the HDMI cable with a better one. Bad HDMI cable can cause data lost. • Press HDMI key on remote handset several times to toggle among different HD OUTPUT. • Check the connections. • The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol. • Clean the disc. • There is no disc inside. ("No Disc" appears on the screen). • Insert the disc correctly with the playback side facing down. • Clean the disc. • The unit and disc region number are incompatible. • Condensation may have formed inside the unit due to a sudden change in temperature. Wait about an hour for it to clear and try again. • Ensure that the video file has been converted to DivX format using the DivX Plus Player on your PC or MAC. • Not all video files are encoded to allow for playback on DivX Certified® products. • Some video files may have been encoded with errors. • Reset the unit, press the STANDBY/ON button to turn off the unit, wait for a few seconds, then restart the unit. - 3 - Unit Front Panel control reference guide 1 235 9 10 Rear Panel 4 678 12 14 15 To wall outlet 11 13 1. DISC TRAY Opens or closes the tray by pressing the OPEN/CLOSE button. 2. REMOTE SENSOR Receives the remote control unit signals. 3. DISPLAY WINDOW Display units information. 4. Power Indicator Indicator Off: The unit is turned on. Indicator On: The unit is in standby mode. 5. ON/STANDBY Button Turns the unit on or puts it in standby mode. 6. OPEN/CLOSE Button Opens or closes the tray. 7. PLAY Button Starts or resumes playback of a disc. 8. SOURCE Button Selects input sources. 9. SD card slot 10. USB port 11. OPTICAL OUT jack 12. HDMI OUT jack 13. VIDEO OUT jack 14. DIGITAL COAXIAL AUDIO OUT jack 15. LEFT/RIGHT AUDIO OUT jacks Remote Control 1. OPEN/CLOSE Button Press to open or close the disc tray. 2. STANDBY/ON Button Press to turn on the unit or put it in standby mode 3. AUDIO Button Press to select one of the audio sound tracks programmed on a DVD or to select the audio output mode on an audio CD. 4. ANGLE Button Press to switch the camera angle of the video presentation when scenes with multiple camera angles are recorded on a DVD. 5. MEMORY Button Press to create programs. 6. DISPLAY Button Press to change disc status information displayed on the TV screen. 7. SETUP Button Press to open or close the SETUP menu screen 8. CURSOR ( , , , ) Button Press to highlight selections on a menu screen and adjust certain settings. OK Button Press to confirm selections on a menu screen. 9. CLEAR Button Clear input selections and cancel certain playback functions. 10. PLAY Button Press to start playback. 11. STOP Button Press to stop playback. 12. SEARCH Button Fast reverse playback. 13. REV Button Press to move backwards through titles, chapters or tracks on a disc. 14. Number (0-9) Buttons 15. A-B REPEAT Button Press to perform point-to-point repeat playback on a DVD or CD. 16. SOURCE Button Selects input sources. 17. SUBTITLE Button Press to select one of the subtitle languages programmed on a DVD. 18. ZOOM Button Zoom in an image. 19. RETURN Button Press to return to normal operation after using SETUP or go to DISC MENU if available. 1 2 43 65 7 8 9 10 11 13 12 14 15 16 17 18 19 20 21 22 24 23 25 26 27 28 20. TITLE Button Press to open the title menu screen. 21. MENU Button Press to open or close the DVD's menu. 22. HDMI Button (for HDMI connection only) Press once to view current HDMI output resolution. Press repeatedly to change resolution (Auto, 480P, 720P, 1080i, or 1080P). 23. PAUSE Button Press to pause playback, frame advance. 24. SEARCH Button Fast forward playback. 25. NEXT Button Press to move forward through titles, chapters or tracks on a disc. 26. SLOW Button Press to perform slow forward playback of DVDs. 27. GOTO Button Press to skip directly to a specific location on a DVD. 28. DISC REPEAT Button Press to repeat chapter or title of a DVD. Press to repeat single track or whole CD. - 4 - white red yellow white red SETUP and connections CONNECTING TO A TV TV The unit can be connected to your TV in several different ways, depending on the design of your TV. Note: Use only one of the below listed connection method for connecting to your TV. AV cable A. RCA AUDIO/VIDEO JACKS Use the Audio/Video cable (included). Connect the VIDEO OUT and left/right AUDIO OUT jacks on the unit to the VIDEO IN and left/right AUDIO IN jacks on your TV. DRC279RE B. CONNECTING TO A DISPLAY (Using a HDMI cable) For TVs that support it, HDMI can provide the best quality audio and video output (depending on media source), and so is the preferred connection type. The HDMI cable incorporates both audio and video signals, so you will have just one cable running from the unit to your TV. Using the HDMI cable (not included), connect the HDMI OUT jack on your unit to the HDMI IN jack on your TV or HDMI-compatible display. • Set an output signal from the HDMI terminal of the DVD player in accordance with your TV's input signal • When using HDMI cable, set the "Digital Out" menu under "Audio" menu to be "PCM (STEREO)" • Press the HDMI button on the remote control to change output signals as below: 480p (progressive) 720p (progressive) 1080I (interlace) 1080p (progressive) Note: • Refer to your owner's manual to the connected TV as well. • When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before making any connections. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC. CONNECTING TO OPTIONAL EQUIPMENT (AMPLIFIER) A. ANALOGUE CONNECTION Using an audio/video cable, connect the left/right AUDIO OUT jack on your unit to the AUDIO IN jack on your other source. ANALOGUE CONNECTION Amplifier of stereo system, etc. AUDIO IN B. DIGITAL CONNECTION Using a coaxial digital audio cable (not included), connect the DIGITAL COAXIAL OUT jack on your unit to the DIGITAL AUDIO IN jack on your other source. DIGITAL CONNECTION Audio equipment with digital audio input jack DIGITAL AUDIO IN Audio cable (red and white) DRC279RE Coaxial Digital Audio cable DRC279RE Note: • When you connect the unit to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections. • If the external equipment is television and this audio system is close to it, you may experience the interference if the tuner function is selected while the television is working. • Refer to the instruction manual of the connected equipment as well. USING USB PORT You can connect a USB flash driveS (not included) to the USB port on the unit to play DivX® movies as well as picture files. • Plug the USB flash drive into the USB port on the unit. • Press SOURCE button to select USB mode. For operation of file playback on the USB flash drive, please refer to the section "PLAYING DivX® VIDEO OR PICTURE FILES". Note: • It is recommended USB flash drive is plugged when the unit is in STANDBY mode. • It does not support USB harddisk mass storage device, multi-card reader and other USB computer peripheral. • It only supports USB flash drive (FAT32/16 max. capacity 32G bytes, video bitrate is 7Mbps). • Make sure your USB flash drive or SD card is FAT16/FAT32 file system. All other file system will not be supported. USING SD CARD SLOT You can connect a Secure Digital (SD) card (not included) to the memory card slot on the unit to play DivX movies as well as picture files. • Plug the SD card fully into the memory card slot on the unit until it clicks. • Press SOURCE button to change to memory card mode. It reads the information of the SD card and playing the picture and/or sound files. For operation of playing files on the SD card, please refer to the section "PLAYING DivX® VIDEO OR PICTURE FILES". Note: • It is recommended the SD card is plugged when the unit is in STANDBY mode. • If the SD card is oriented incorrectly, it will not go fully into the slot. Do not apply force when inserting the SD card. • To remove the SD card, push the CD card into the slot and then slowly remove your finger, the lock is released and the SD card is pushed out. - 5 - DRC288SU IB ENG.indd 1 5/12/2010 12:19:16 PM