RCA HD61THW263 User Manual - Page 79

Loosen the screw on the door don't remove the screw, just loosen it. - lamp replacement

Get RCA HD61THW263 PDF manuals and user guides View all RCA HD61THW263 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

References ___ The correct lamp replacement unit. To order the correct lamp, you'll need to know your TV's model number, serial number, and lamp type. The TV's model number is located under the front panel piece towards the bottom left corner. Go to page 10 for information on removing the front panel piece. The serial and lamp part numbers are listed on the Service Model Number sticker (example shown on the right). The sticker is located on the lamp handle (see the following page for sticker location). ___ The box that the lamp replacement unit came in. 1. Read the precautions listed above. CAUTION ! - HOT PRECAUCIÓN - CALIENTE ATTENTION - CHAUDE LAMP PART # - 265109 41030325110090 BAR CODE AREA EXAMPLE: Service Model Number sticker with lamp part number listed. 2. Make sure your hands are dry and clean before you begin replacing the lamp. 3. Unplug the TV's power cord from the wall outlet (or power strip). Unplug the power cord from the back of the TV. 4. Put the power cord far away from the TV. Taking this precaution will ensure that no one plugs in the TV if you walk away from it, or when you're waiting for the lamp unit to cool, or when you're installing the new lamp. 5. Wait 1 hour so the lamp can thoroughly cool. If you don't wait at least 1 hour, you risk getting injured! 6. After 1 hour, go to the front of the TV set and remove the front panel piece. Go to page 10 for instructions. Find the lamp-unit access door (located in the lower right side of the TV). Read the precautions on the door (you may need a flashlight). Note: Do not attempt to repair the lamp. Do not open the lamp assembly unit - leave the lamp in its casing. 7. Loosen the screw on the door (don't remove the screw, just loosen it). Note: Don't use a coin to loosen the screw because the coin could fall into the TV. Chapter 5 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
References
Chapter 5
77
___
The correct lamp replacement unit. To order the correct lamp, you’ll need to know
your TV’s model number, serial number, and lamp type. The TV’s model number is located
under the front panel piece towards the bottom left corner. Go to page 10 for information
on removing the front panel piece. The serial and lamp part numbers are listed on the
Service Model Number sticker (example shown on the right). The sticker is located on the
lamp handle (see the following page for sticker location).
___
The box that the lamp replacement unit came in.
6.
After 1 hour, go to the front of the TV set and remove the front panel
piece. Go to page 10 for instructions. Find the lamp-unit access door
(located in the lower right side of the TV). Read the precautions on the
door (you may need a flashlight).
Note:
Do not attempt to repair the lamp. Do not open the lamp
assembly unit — leave the lamp in its casing.
7.
Loosen the screw on the door (don’t remove the screw, just loosen it).
Note:
Don’t use a coin to loosen the screw because the coin could fall
into the TV.
EXAMPLE: Service
Model Number
sticker with lamp
part number
listed.
1.
Read the precautions listed above.
2.
Make sure your hands are dry and clean before you begin replacing the lamp.
3.
Unplug the TV’s power cord from the wall outlet (or power strip). Unplug the power cord from the back of the TV.
4.
Put the power cord far away from the TV. Taking this precaution will ensure that no one plugs in the TV if you walk
away from it, or when you’re waiting for the lamp unit to cool, or when you’re installing the new lamp.
5.
Wait 1 hour so the lamp can thoroughly cool. If you don’t wait at least 1 hour, you risk getting injured!
CAUTION ! – HOT
PRECAUCIÓN – CALIENTE
ATTENTION – CHAUDE
LAMP PART # - 265109
41030325110090
BAR CODE AREA