Rane CP64S CP64S Installation Manual - Page 14
do
View all Rane CP64S manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
7 2 24 24 PAGING ZONE ASSIGN LEVEL PAGE 1 PAGE 2 ZONE 1 ZONE 2 12 12 4 6 4 6 RMT 1&2 RMT 1&2 ACTIVE 0 10 0 10 ACTIVE PROGRAM INPUT LEVELS ZONE 1 ZONE 2 LINE 1 4 6 0 10 LINE 2 4 6 0 10 LINE 3 4 6 0 10 PRIORITY 4 6 DUCKER PROGRAM DEPTH SELECT L2 L3 L1 P RMT LEVEL 4 6 DUCKER PROGRAM DEPTH SELECT L2 L3 L1 P RMT LEVEL 4 6 OFF ON 0 10 OFF ON 10 SIG OL 10 SIG OL ZONE 1 ZONE 2 + 12 • 6 • 0 • 6 • 12 40 100 250 630 1.6k 4k 10k 40 100 250 630 1.6k 4k 10k CP64S COMMERCIAL PROCESSOR POWER 80 80 q 1 CP64S COMMERCIAL AUDIO 100-240 V EQUIPMENT 24TJ 50/60 Hz 12 WATTS R Z2 PGM Z2 LEVEL REMOTES WIRING MIN MAX Vr Vc OUTPUTS Z2 EXPAND Z2 MONO ALL AUDIO AND REMOTES ARE CLASS 2 WIRING ZONE 2 ZONE 1 EXPAND OUT EXPAND OUT ZONE PAGE ZONE PAGE RANE CORP. MADE IN U.S.A. ACN 001 345 482 Z1 PGM D1 D0 Z1 LEVEL Vr Vc 2 PGM 1 PGM Z1 EXPAND Z1 RIGHT Z1 LEFT +- +- +- PROGRAM INPUTS LIMITER PRIORITY ZONE 1 ZONE 2 ASSIGN ZONE L L +8 +8 off 1 2 -20 +20 -20 +20 R R 1&2 PRIORITY 3 2 1 REMOTE PAGE REMOTE 1 INPUT 1 ZONE ASSIGN WIRING Z1 Z2 PAGING INPUTS PAGE 2 TRIM PAGE 1 TRIM PAGE 2 PAGE 1 DETECT THRESHOLD REMOTE 2 INPUT 2 Z2 Z1 +- +30 +60 OL +30 +60 MIC LINE MIC LINE 29 67 57 ...CP64S Calibration (continued) 1 Connect the power cord and verify the Power indicator lights. 2 Verify Zone Level controls are set to Maximum and that you have an active source for each of the Program Inputs you intend to use. Select each Program Input and adjust its Input Level control to be the very loudest you would ever desire. 3 Adjust the rear panel Zone Limiter thresholds so that they just start to audibly reduce the output level. This ensures the level in a Zone will never be louder than the maximum level you just set. If you wish one of the Zones to have a lower maximum loudness, lower the Zone Limiter threshold accordingly. 4 Turn the Zone Level controls down to a comfortable listening level. 5 Note that with the Paging Zone Level set to minimum, you will not hear the following Page. Speak very loudly (bark) into the Paging Mic. Set the proper preamplifier gain by adjusting the Page Trim control (rear panel) so the Page OverLoad Indicator (rear panel) just lights. It is important to set the gain of the pre-amp before setting the Page Detect Threshold. Repeat for the second Mic if it is used. 6 Speak into the Page Mic in a normal voice and adjust the Page Detect Threshold (rear panel) so the Active indicator (front panel) lights only when you speak. If the Page Detect Threshold is set too low, the Pager may gate on due to background sound. Repeat for second Mic if used. 7 With an active Program source playing in both Zones, speak into the Page Mic. Adjust the Zone 1 and Zone 2 Paging Level controls (front panel) to provide the correct Page-to-Program mix in each zone. If the Page Detect Threshold is set too high, there may be a delay when you start to speak. To correct, lower the Page Detect Threshold setting. If a second Page source is used, verify that it has the same level as the first Page source (it should be close). If not, use the Page Trim control of the second Page source to adjust its gain to match. If you change the gain of the second Page source substantially, be sure to reset the Page Detect Threshold. 8 Set the Ducker switch to ON. With an active Program source playing, speak into the Page Mic and adjust the Ducker Depth as required. Repeat for both Zones. 9 Set the Program Priority Assign Zone switch as required (on rear panel). If you do not require automatic priority program override in a zone, do not assign it. Instead, use the front panel Program Select switch to select the "P" program Input as you would any other non-priority input. 0 If a remote control is used, select the appropriate RMT switch settings on the front panel to verify the remote functions correctly. q Adjust the Equalizers as required. ...You're all set. 14