Rane MP25 MP25 Mixer Owners Manual - Page 9

MP25 CLUB MIXER IC 2 6 8 10 EVEL RIGHT PAN +6 HIGH +6 LOW EXFX C ON KOVER Phones PGM 1 PGM 2 PGM 3 PGM 4 D1 A1 TA2hA3e HeadphoneDM2 A1oAn2iAt3or provides stDe3rAe1oA2oAr3 mono Split CD4uAe1 A2 A3 P1 opeAr4ation. P2 A4 P3 A4 P4 A4 FLEXFX 46 2 8 ZONE 4 6 2 8 MAIN 4 6 2 8 • In StOeFFreo+6operation, the OPFFan+c6ontrol pans betOFwF ee+n6 stereo Cue S4OURC6Eand thHIeGHstereoSM4OUaRiC6nE Mix.HIGH SOURCE 4 6 HIGH SOURCE 4 6 • In Split Cue operation, the Pan control pans between Mono 2 8 2 8 2 8 2 8 Cue in the left ear and mono Main Mix in the right ear. 0 10 OFF +6 0 10 OFF +6 0 10 OFF +6 0 10 • LEVEL IndiviMdIuD al CueLbEVuEtLtons arMeIDprovidedLEVfEoLr PGMM1ID, PGML2EV,EL PGM 3, PGM 4 and the FlexFX Loop. • The Headphone Level control sets the level in both the front OFF +6 HIGH OFF +6 MID 0 10 SEND EXT LOOP 4 6 2 8 0 10 USB LOOP RETURN 46 0 10 LEVEL OL +6 +3 0 -3 -6 0 10 LEVEL LEFT RIGHT BALANCE panel 3.5 mm and ¼˝ output jacks. LOW HIGH FILTER OFF +6 LOW LOW HIGH FILTER OFF +6 LOW LOW HIGH FILTER OFF +6 LOW LOW HIGH FILTER • TheAheadpB hone output inA cludBes 2-band full-Acut toBne controls. Tone PcOoSTntrol range is Off toPOST+6 dB. These heaPdOpSThone tone FLEXFX 10 FLEXFX 10 FLEXFX 10 FLEXFX 10 c9ontrols are adjusted 9from the computer u9 sing the MP25 9 d8river control panel. 8 CUE 7 CUE 7 8 CUE 7 8 CUE 7 OFF +6 LOW A B POST 2 8 CUE -12 0 10 -18 LEVEL FLEXFX ON CONTOUR MONO FLEXFX MP25 CLUB MIXER Ma6in Mix and Main/6 Zone Outputs 6 6 5 5 5 5 The4Main Mix is made 4from MIC 1, MIC 24, PGM 1, PGM 2, 4 PGM3 3, PGM 4 and th3e FlexFX Mix. 3 3 • M2 ono the Main Mix2by pressing the fron2t panel Mono but- 2 1 1 1 1 to0 n. To mono only a 0specific output, use 0the rear panel Mono0 switch on the Main Outs, or the auto-mono single plug feature of the Zone and Booth Outs. • Apply effects to the entire Main Mix by engaging the Main Mix (blue) FlexFX button. This button instantly sends PGMs 1-4 and Mic 1-2 to the FlexFX Bus. • The Main Mix is metered using a stereo rms/peak signal meter with peak-hold. Magnetic Crossfader The MP25's crossfader is a field replaceable, no-noise, no-bleed magnetic fader. • Assign each PGM channel to the A-side, B-side or Post-Cross- The Main Mix feeds these outputs: • Main Outs fader with switches in the program strips. • Select one of three crossfader slopes with the Contour switch. • Front panel Balance and Level controls manage the relative (left/right) and overall levels respectively. • The rear panel Mono switch combines the left and right channels of the Main output, and an attenuator controls the Max Out dB from 8 Vrms (0 dB) to 0.5 Vrms (-24 dB). • The Main Output is available on balanced XLR and unbalanced RCA connectors. • Booth and Zone Outs • Front panel Booth and Zone Level controls adjust the cor- Crossfader Questions and Answers Q: Can I install magnetic crossfaders in any other mixer? A: The connectors may be similar, but the circuits are very differ- ent. Connecting the fader to anything other than the intended cable in the MP25 could permanently damage it. Q: Can I install another crossfader in my MP25? A: No. The cable connections are specially designed for Rane magnetic faders. responding output level. • Booth and Zone Outputs are available on balanced ¼˝ See "Faders" on page 14. TRS jacks. Left and right jacks automatically provide a mono signal if the other plug is not inserted. • Record Outs • Stereo unbalanced RCA and S/PDIF outputs. • The S/PDIF output is a 24-bit 48 kHz digital output. • The Main Mix, Mic 1, or Mic 2, may be recorded via USB record channel six. Record source selection is made in the computer's MP25 driver control panel. 9